Skip to Content

Register Login

Industry Online Support

Technical Forum

Navigation

S7 1200 error code

Created by: Denza at: 10/22/2012 1:05 PM (5 Replies)

Rating (1)

Thanks 1

6 Entries

10/22/2012 1:05 PM	Rate (0)
Denza Posts: 13 Rating: (0)	Hello, I have S7 1200 with few cards (AI,AQ,DQ....) and HSC724i, everything was OK, until today, when I try to load my programm to PLC the TIA notify me about error (error code: 0xa24ab0001c2ff14) and stop all, ther is no description about this error, so I can't load my program do PLC. Does anyone have error code list or tell me whot to do...... I need this urgently
Denza Posts: 13 Rating: (0)
Suggestion To thank Quote Answer

10/22/2012 5:40 PM	Rate (1)
0_Einstein Diamond Expert Joined: 7/7/2010 Last visit: 1/17/2025 Posts: 15541 Rating: (2465)	Denza Hello, I have S7 1200 with few cards (AI,AQ,DQ....) and HSC724i, everything was OK, until today, when I try to load my programm to PLC the TIA notify me about error (error code: 0xa24ab0001c2ff14) and stop all, ther is no description about this error, so I can't load my program do PLC. Does anyone have error code list or tell me whot to do...... I need this urgently I have seen several kinds of error codes that prevent me from reloading the plc. I had one case where the HMI and my PC application were both still communicating with the PLC when I did a full download. The plc went into fault and would not restart. I power cycled the plc, and my newly installed changes took effect and it went into run mode. Once I disconnected the ethernet cables from everything trying to communicate while I was downloading, it worked and no more error codes. Sometimes you may need to perform the online function to reset the plc to factory defaults (keep the ip address), and then reload your program. Post your results!
	Last edited by: huggy_d1 at: 10/22/2012 5:41 PM science guy
Suggestion To thank Quote Answer

10/23/2012 9:20 AM	Rate (0)
Denza Posts: 13 Rating: (0)	I restarted the plc on factory setings and look my program, there was olso a litle mistake in my program, I corrected and loaded again and now everithing works again. Anyway thanks for your help
Denza Posts: 13 Rating: (0)
Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users DarshanS

3/19/2013 1:02 PM	Rate (0)
DarshanS Experienced Member Joined: 12/3/2010 Last visit: 12/10/2024 Posts: 31 Rating: (1)	That error does not report any diagnostice in module information online. If it due to program then it should give programming error in Diagnostic buffer.

Suggestion To thank Quote Answer

2/5/2016 12:38 PM	Rate (0)
Min_Moderator Platinum Member Joined: 9/3/2014 Last visit: 3/13/2019 Posts: 4766 Rating: (122)	New question published by ss16 is split to a separate thread with the subject Error while downloading logic to s7-1200. Best regards Min_Moderator

Suggestion To thank Quote Answer

2/6/2016 9:09 AM	Rate (0)
Saeed Bahadori Posts: 63 Rating: (8)	you can search HSC sample and see how an expert member creat it !
Saeed Bahadori Posts: 63 Rating: (8)	Last edited by: sbj at: 2/6/2016 9:09:59 AM Last edited by: sbj at: 2/6/2016 9:25:15 AM
Suggestion To thank Quote Answer

|

Share this page:

Share this page on...

Follow us on