Skip to Content

Register Login

Industry Online Support

Technical Forum

Navigation

S7-1200 extended module malfunctioning

Created by: dearj06 at: 6/7/2022 11:53 PM (7 Replies)

Rating (0)

Thanks 2

8 Entries

6/7/2022 11:53 PM	Rate (0)
dearj06 Member Joined: 12/15/2016 Last visit: 1/17/2023 Posts: 10 Rating: (0)	I am using s7-1200 1214C AC/DC/RLY(6es7 214-1bg31-0xb0) with extended module 16DI/16D0 SM 1223 DC/RLY (6es7 223-1pl32-0xb0). I am having issue in extended module if some one could tell me the cause. I enabled the output of extended module from inputs however the output is not working, there is no output voltage coming out or heard any relay energizing sound from that module why is that? Even though output leds are turning on but zero volt on terminal side. Hardware configuration is perfect even the wiring is also done as per the manual.

Suggestion To thank Quote Answer

6/8/2022 1:27 AM	Rate (0)
dchartier Grandmaster Joined: 9/27/2006 Last visit: 1/29/2023 Posts: 11946 Rating: (2562)	Hello dearj06; The symptoms you describe generally appear when the user has omitted to wire power to the outputs on the SM module. Please review the wiring diagram fir the SM1223-1PL32, attached below and check all the power connections, including the 24 V L+/M- connections on all the output groups. Hope thus helps, Daniel Chartier Attachment Screenshot_20220607-192029_Chrome.jpg (178 Downloads)
	Last edited by: dchartier at: 06/08/2022 01:29:31
Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users PISCEAN 2010

6/8/2022 8:01 AM	Rate (0)
dearj06 Member Joined: 12/15/2016 Last visit: 1/17/2023 Posts: 10 Rating: (0)	i followed the drawing but still not working Attachment WhatsApp Image 2022-06-08 at 8.59.29 AM.jpeg (180 Downloads)

Suggestion To thank Quote Answer

6/8/2022 8:26 AM	Rate (0)
AutoGen_463075 Regular Member Joined: 4/28/2015 Last visit: 1/27/2023 Posts: 22 Rating: (1)	Hello, your wiring looks fine. I would now check your lamp. Possibly the polarity is reversed or it is defective. And I would check the relay on the EM. Measurement with an Ohm meter. When the relay switches, 0 ohms must be measurable. Greetings Georg

Suggestion To thank Quote Answer

6/8/2022 5:20 PM	Rate (0)
0_Einstein Diamond Expert Joined: 7/7/2010 Last visit: 1/27/2023 Posts: 13080 Rating: (2123)	Might not matter, but I have comments about (at least) 2 things. 1. Why is the cover removed? You should not do that. It is not user serviceable. 2. The Ground terminal is not connected to earth. On the digital outputs, I see 2 wires for L+ and M. I tried to trace the wiring by eye from the posted image, but the orb got me confused and I could not tell what was happening. The module power L+ and M (next to the ground terminal) are not coming from the same source as the DQ's. Why? I see the first 5 DQs lit. That requires more wires than you have connected in order to fully work. 1L is for .0 to .3 on the bottom section - top terminal block. 2L is for .4 to .7 on the bottom section - top terminal block. 2L is not connected, so .4 (shown as activated by LED) is not going to work. dearj06 i followed the drawing but still not working
	science guy
Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users dchartier

6/10/2022 3:30 PM	Rate (0)
AutoGen_463075 Regular Member Joined: 4/28/2015 Last visit: 1/27/2023 Posts: 22 Rating: (1)	Hello @ dearj06: Do you have new insights? Nevertheless, I want to write my view on 0_Einstein's objections. - I also see opening the case as not necessary. - It is not necessary to connect the minus potential to earth. These are modules that can work with both a SELV and a PELV voltage. - Also, the block of 4 relay outputs does not have to be connected to the supply of the module. Because that's the idea behind it. Thus, other potentials can also be switched. Like 230V AC. - The first 5 LEDs light up. Thus, output x.0 to x.4 are activated. 1L for x.0 to x.3 is connected. Thus, a voltage should be measurable at x.0. Here you go to the lamp and then further back to the minus of the power supply. Right in my eyes. Except that the lamp doesn't light up. Hence my guess. Lamp defective. Or the polarity of the lamp is reversed (if it is an LED), or the relay does not pick up, so that the +24V does not reach the lamp. Greeting Georg
	Last edited by: AutoGen_463075 at: 06/10/2022 16:19:34
Suggestion To thank Quote Answer

6/14/2022 2:31 PM	Rate (0)
dearj06 Member Joined: 12/15/2016 Last visit: 1/17/2023 Posts: 10 Rating: (0)	Problem solved! The problem is in its input 24vdc supply section. Thanks all of you for your valuable suggestions.

Suggestion To thank Quote Answer

6/14/2022 3:12 PM	Rate (0)
0_Einstein Diamond Expert Joined: 7/7/2010 Last visit: 1/27/2023 Posts: 13080 Rating: (2123)	Please explain? Or, do you mean the 24VDC supply (meant to supply switches and relay contacts) was getting overloaded by how it was being used, or it failed completely? dearj06 Problem solved! The problem is in its input 24vdc supply section. Thanks all of you for your valuable suggestions.
	science guy
Suggestion To thank Quote Answer

|

Share this page:

Share this page on...

Follow us on