Skip to Content

Register Login

Industry Online Support

Technical Forum

Navigation

S7300 DO Problems

Created by: Running Hill at: 1/27/2011 2:10 PM (16 Replies)

Rating (0)

Thanks 3

Result pages:: |; 1 | 2; |

17 Entries

Entries per page: 10 | all

1/27/2011 3:52 PM	Rate (0)
Running Hill Posts: 9 Rating: (0)	hdhosseini Dear running hill please check other channels in the DO cards are actives such as Q5.1 or Q5.7 as shown in the picture. if they are active in sotware and active in hardware there is a problem with indicator LED of Q5.4.You measure voltage of the output to be sure. BR I checked 5 other Qx.x with your suggestion and non of them indicates "ON"on the PLC.
Running Hill Posts: 9 Rating: (0)
Suggestion To thank Quote Answer

1/27/2011 3:56 PM	Rate (0)
UMENCHO Diamond Member Joined: 3/21/2006 Last visit: 11/1/2024 Posts: 10229 Rating: (1181)	Depends from type of DO module check if wiring there is correct.

Suggestion To thank Quote Answer

1/27/2011 4:04 PM	Rate (0)
hdhosseini Diamond Expert Joined: 1/28/2009 Last visit: 10/26/2024 Posts: 6852 Rating: (1365)	Running Hill I checked 5 other Qx.x with your suggestion and non of them indicates "ON"on the PLC. 1- Back up current project 2- Create a new project with a simple hardware in your set up 3- download the harware configuration and then FORCE all DO one by one.Check if supply of Do module available and also Back plane connector also available on RACK. BR
	Demo Channel on Youtube
Suggestion To thank Quote Answer

1/27/2011 4:08 PM	Rate (0)
Running Hill Posts: 9 Rating: (0)	UMENCHO Depends from type of DO module check if wiring there is correct. I measured 24V+ on the DO module power point.
Running Hill Posts: 9 Rating: (0)
Suggestion To thank Quote Answer

1/27/2011 4:16 PM	Rate (0)
hdhosseini Diamond Expert Joined: 1/28/2009 Last visit: 10/26/2024 Posts: 6852 Rating: (1365)	Hi Check if between all modules there is a Back plane connector on RACK. BR
	Demo Channel on Youtube
Suggestion To thank Quote Answer

1/27/2011 4:55 PM	Rate (0)
Running Hill Posts: 9 Rating: (0)	hdhosseini Hi Check if between all modules there is a Back plane connector on RACK. BR How I hope there's no back plane, but unfortunately yes. And no broken up in the plane connector. And I followed your suggestion to force every output with a simple logic, butstill no evolving. ...........
Running Hill Posts: 9 Rating: (0)
Suggestion To thank Quote Answer

1/29/2011 4:21 PM	Rate (0)
Running Hill Posts: 9 Rating: (0)	Dear all, With all your suggstion and help I finally find out that there's problem in the DO module. We disassembled the module and test the circuit with the multimeter after which we found asemiconductor elementin the circut was breakdown and coursed short then melt the 7A fuse between the 24V and the circuit. Thank you all for your help!
Running Hill Posts: 9 Rating: (0)	Last edited by: Running Hill at: 1/29/2011 4:24 PM Last edited by: Running Hill at: 1/29/2011 4:21 PM
Suggestion To thank Quote Answer
This contribution was helpful to 3 thankful Users UMENCHO hdhosseini O_Moderator

|

Share this page:

Share this page on...

Follow us on