Skip to Content

Register Login

Industry Online Support

Technical Forum

Navigation

Simodrive611/810D lost data & PB problem

Created by: TomTav at: 4/26/2022 5:19 PM (22 Replies)

Rating (0)

Thanks 1

Result pages:: |; 1 | 2 | 3; |

23 Entries

Entries per page: 10 | 20 | all

4/28/2022 12:35 PM	Rate (0)
TomTav Regular Member Joined: 3/14/2022 Last visit: 12/17/2022 Posts: 15 Rating: (0)	See the screenshot above from SimocomU, it shows the LT Module.

Suggestion To thank Quote Answer

4/28/2022 12:39 PM	Rate (0)
TomTav Regular Member Joined: 3/14/2022 Last visit: 12/17/2022 Posts: 15 Rating: (0)	The Info i still didnt find in the Siemens Docs is if and how the Drive Konfiguration is transfered from the Sinumerik to the "external" 7th Axis with the Simodrive611. What i did find is that Simocom can talk to this Firmware (3.02) only via serial port, Profibus Konfiguration is only possible from FW 3.1 up. So if the Sinumerik does the restore to 611 via Profibus, it possibly couldnt be possible on this Konfiguration ... this is just a assumption on my side

Suggestion To thank Quote Answer

4/28/2022 12:48 PM	Rate (0)
PISCEAN 2010 Diamond Expert Joined: 4/23/2010 Last visit: 12/31/2023 Posts: 8092 Rating: (878)	TomTav See the screenshot above from SimocomU, it shows the LT Module. Screenshot is not complete. Does green LED is displayed? It means on line connection is established or else it displays only connection with memory module. Another point is, it does not confirms axis communication with NC.
	Last edited by: PISCEAN 2010 at: 04/28/2022 13:09:09 not added
Suggestion To thank Quote Answer

4/28/2022 12:48 PM	Rate (0)
TomTav Regular Member Joined: 3/14/2022 Last visit: 12/17/2022 Posts: 15 Rating: (0)	This is the par file when i read out the Simodrive via Simocom / RS232, for me it looks like unconfigured. I just changed the Profibus address from 0 to 30 (which is the correct one for this machine) Attachment simocom.par.zip (478 Downloads)
	Last edited by: TomTav at: 04/28/2022 12:49:00
Suggestion To thank Quote Answer

4/28/2022 12:50 PM	Rate (0)
TomTav Regular Member Joined: 3/14/2022 Last visit: 12/17/2022 Posts: 15 Rating: (0)	The Fault Led is red, the Led on the Profibus Option module is green (after setting the DP address)

Suggestion To thank Quote Answer

4/28/2022 12:50 PM	Rate (0)
PISCEAN 2010 Diamond Expert Joined: 4/23/2010 Last visit: 12/31/2023 Posts: 8092 Rating: (878)	TomTav [snip] So if the Sinumerik does the restore to 611 via Profibus, it possibly couldnt be possible on this Konfiguration ... this is just a assumption on my side As discussed in my previous reply, attach the snapshot of service diagnosis screen (which you mentioned spindle axis is not detected)

Suggestion To thank Quote Answer

4/28/2022 12:52 PM	Rate (0)
TomTav Regular Member Joined: 3/14/2022 Last visit: 12/17/2022 Posts: 15 Rating: (0)	Sorry, here is the complete screen shot You are talking about HMI screenshot? Wait a minute Attachment TeamViewerScreenSnapz004.png (435 Downloads)
	Last edited by: TomTav at: 04/28/2022 12:53:00
Suggestion To thank Quote Answer

4/28/2022 12:55 PM	Rate (0)
TomTav Regular Member Joined: 3/14/2022 Last visit: 12/17/2022 Posts: 15 Rating: (0)	This one? Attachment TeamViewerScreenSnapz005.png (508 Downloads)
	Last edited by: TomTav at: 04/28/2022 12:55:19
Suggestion To thank Quote Answer

4/28/2022 12:59 PM	Rate (0)
TomTav Regular Member Joined: 3/14/2022 Last visit: 12/17/2022 Posts: 15 Rating: (0)	I think the 611U is just controlled by PLC via Profibus on this machine. I have no errors, except when i try to start the machine. Then i get all the Spindle related errors

Suggestion To thank Quote Answer

4/28/2022 1:14 PM	Rate (0)
PISCEAN 2010 Diamond Expert Joined: 4/23/2010 Last visit: 12/31/2023 Posts: 8092 Rating: (878)	TomTav [snip] In HMI i can just see the 5 axes connected to 810D, but not this axis (its the spindle). This screenshot where you can not see spindle axis.

Suggestion To thank Quote Answer

|

Share this page:

Share this page on...

Follow us on