Skip to Content

Register Login

Industry Online Support

Technical Forum

Navigation

SINAMICS G120C UPLOAD ERROR - DIFFERENT VERSION

Created by: hadok at: 4/1/2020 8:41 AM (7 Replies)

Rating (0)

Thanks 0

8 Entries

4/1/2020 8:41 AM	Rate (0)
hadok Experienced Member Joined: 4/28/2015 Last visit: 11/28/2023 Posts: 65 Rating: (4)	Hello for all. My system is Win10 x64 TIA 15.1 UPD4 Sinamics Startdrive V15.1 Upd3 + Options G120C V15.1 Upd3 I tried to make upload of the parameters from inverter to my project. But always i had the same error that say: The configured device does not correspond to the target device. Please check the order numbers. Off course it was my first thing to do, to check the versions . They are equal 4.7.10. As you can see at my attached multiscreenshot the versions are 4.7. SP 10 (ONLINE ) and 4.7.10 (OFFLINE.). Only the camp is different BUILD V04.71.15.04 - but i don;t know if it is important. But i can go to the ONLINE with this inverter, i can see and change the parameters, i can download to the inverter normally. But when try to make UPLOAD - error. I had this situations several times with G120C and would like to understand where i did wrong settings. Thank you for any advice and help. Attachment Upload_G120C.jpg (254 Downloads)

Suggestion To thank Quote Answer

4/1/2020 9:22 AM	Rate (0)
RB91 Gold Member Joined: 4/28/2015 Last visit: 9/20/2022 Posts: 1278 Rating: (292)	Hello, strange error, only thing I could imagine is that you are still online with the PLC in the TIA project (this lead to error messages for me in some cases). But I am not sure if the error then would be a different one. So ensure that all devices in the project are offline.
	Best regards, Robert
Suggestion To thank Quote Answer

4/1/2020 9:40 AM	Rate (0)
hadok Experienced Member Joined: 4/28/2015 Last visit: 11/28/2023 Posts: 65 Rating: (4)	RB91 Hello, strange error, only thing I could imagine is that you are still online with the PLC in the TIA project (this lead to error messages for me in some cases). But I am not sure if the error then would be a different one. So ensure that all devices in the project are offline. Yes, sure. If i am still online the error will be like The master of network connection....... So i tried in OFFLINE mode only.....

Suggestion To thank Quote Answer

4/1/2020 10:20 AM	Rate (0)
Technology Team Platinum Expert Joined: 10/11/2006 Last visit: 11/29/2023 Posts: 5711 Rating: (771)	Hello, please involve the technical support: https://support.industry.siemens.com/my/ww/en/requests/#createRequest
	With best regards, Technology Team Application consulting and pre sales support for SINAMICS, SIMATIC Technology, SIMOTION, SIMOTICS and MOTION CONNECT
Suggestion To thank Quote Answer

4/1/2020 10:28 AM	Rate (0)
hadok Experienced Member Joined: 4/28/2015 Last visit: 11/28/2023 Posts: 65 Rating: (4)	Technology Team Hello, please involve the technical support: https://support.industry.siemens.com/my/ww/en/requests/#createRequest Done.

Suggestion To thank Quote Answer

3/18/2021 10:27 AM	Rate (0)
BoletusEdulis Silver Member Joined: 6/10/2015 Last visit: 11/20/2023 Posts: 447 Rating: (90)	Hi, what was the result of the support? Thank you
	B. Edulis --- If you have a doubt, there is no doubt
Suggestion To thank Quote Answer

5/18/2023 7:03 AM	Rate (0)
Simone98 Member Joined: 6/4/2018 Last visit: 5/18/2023 Posts: 1 Rating: (0)	HI, I have the same problem, did you happen to find a solution? Thank you!

Suggestion To thank Quote Answer

5/18/2023 1:15 PM	Rate (0)
Hati Platinum Member Joined: 9/21/2012 Last visit: 11/29/2023 Posts: 3798 Rating: (431)	Simone98 HI, I have the same problem, did you happen to find a solution? Describe what you have done and what the error is? Have you checked that the MLFB number is 100% same in the online and offline? Have you checked that the firmware version is 100% in offline and online?

Suggestion To thank Quote Answer

|

Share this page:

Share this page on...

Related topics by keywords:

SINAMICS_G

Follow us on