Skip to Content

Register Login

Industry Online Support

Technical Forum

Navigation

Sinamics G130, CU320, AOP30 Fault F1910 PB Setpoint timeout in local operation with AOP30

Created by: Odin at: 6/16/2010 1:23 PM (7 Replies)

Rating (1)

Thanks 1

8 Entries

6/16/2010 1:23 PM	Rate (0)
Odin Posts: 19 Rating: (0)	I sure hope you can help me with this one. I have a setup with a G130, CU320 and AOP30 for local operation. Remote operation with PLC (317 2PN/DP). Problem is that with Profibus disconnected from CU320 local operation works fine. Profibus conected to CU320 causes a F1910 PROFIBUS: Setpoint Timeout. When AOP30 is set to remote (Local/Remote is lit) setpoint should come from AOP30 and ignore Profibus. Does anyone know how to fix this so that in local operation system only looks at AOP30. *edit: When PLC is in STOP, system does run as expected in local operation. Seems that if there is a Profibus master on the profibus, it expects a setpoint from the profibus master, but I want system to run in local operation from AOP30 with profibus master active. Thx, Odin.
Odin Posts: 19 Rating: (0)	Last edited by: Odin at: 6/16/2010 1:37 PM
Suggestion To thank Quote Answer

6/16/2010 2:06 PM	Rate (0)
Vithani Platinum Member Joined: 7/8/2009 Last visit: 7/26/2023 Posts: 1974 Rating: (475)	What is the status of Binector connected at P0854 in local mode?? Try making P0854 to zero when you set it to Local Mode Regards, Devesh
	I dont Like people driving Fast, thats the reason I overtake them ;)
Suggestion To thank Quote Answer

6/16/2010 3:16 PM	Rate (0)
Odin Posts: 19 Rating: (0)	Vithani What is the status of Binector connected at P0854 in local mode?? Try making P0854 to zero when you set it to Local Mode Regards, Devesh Does not make any difference for the setpoint timeout failure, P0854 set to zero of set to one in local mode. BO: Master Control active p0807 does go to 1 when AOP30 is set to local mode.
Odin Posts: 19 Rating: (0)
Suggestion To thank Quote Answer

6/16/2010 5:49 PM	Rate (1)
Gary.Hare Posts: 101 Rating: (8)	F1910 will appear if the drive sees bit 10 in the control word go from high to low. (expected if the plc is switched off). If you reset this fault the drive should run in local with no problems. If the fact that the fault is occuring in the first place is the problem, you can change F1910 into either an alarm or just amessage so you will not need to reset it at all. - P2118 & P2119
Gary.Hare Posts: 101 Rating: (8)
Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users Zul_Sinumerik

6/17/2010 8:48 AM	Rate (0)
Odin Posts: 19 Rating: (0)	Gary.Hare F1910 will appear if the drive sees bit 10 in the control word go from high to low. (expected if the plc is switched off). If you reset this fault the drive should run in local with no problems. If the fact that the fault is occuring in the first place is the problem, you can change F1910 into either an alarm or just amessage so you will not need to reset it at all. - P2118 & P2119 Thank you, This did the trick! I changed F1910 into a message and now it will run in local operation no problem. Getting really close to a big deadline so thanks a lot. Grtz, Odin
Odin Posts: 19 Rating: (0)
Suggestion To thank Quote Answer

8/25/2020 3:50 AM	Rate (0)
Zul_Sinumerik Regular Member Joined: 6/29/2020 Last visit: 11/16/2023 Posts: 1 Rating: (0)	Thank you for you tips. this one really helpful

Suggestion To thank Quote Answer

11/30/2022 11:03 AM	Rate (0)
12OCT1989 Joined: 11/16/2022 Last visit: 12/20/2022 Posts: 1 Rating: (0)	Odin Gary.Hare F1910 will appear if the drive sees bit 10 in the control word go from high to low. (expected if the plc is switched off). If you reset this fault the drive should run in local with no problems. If the fact that the fault is occuring in the first place is the problem, you can change F1910 into either an alarm or just amessage so you will not need to reset it at all. - P2118 & P2119 Thank you, This did the trick! I changed F1910 into a message and now it will run in local operation no problem. Getting really close to a big deadline so thanks a lot. Grtz, Odin I cant understand how to solve, can you please share me the some picture of parameter or videos.

Suggestion To thank Quote Answer

11/30/2022 11:14 AM	Rate (0)
PISCEAN 2010 Diamond Member Joined: 4/23/2010 Last visit: 12/3/2023 Posts: 8061 Rating: (856)	12OCT1989 Odin Gary.Hare I cant understand how to solve, can you please share me the some picture of parameter or videos. Hello, For example if you want to change F1910 to No Message then in p2118[0] set 1910 value & in p2119[0] set = 3 so that no message will be displayed or if you want to change F1910 to alarm then in p2118[0] set 1910 & in p2119[0] set = 2 so that F1910 will change to alarm & no necessary to acknowledge it. Hope this helps.

Suggestion To thank Quote Answer

|

Share this page:

Share this page on...

Related topics by keywords:

SINAMICS_G

Follow us on