Skip to Content

Register Login

Industry Online Support

Technical Forum

Navigation

Sinaut micro with PAC3200/4200 energy monitor

Created by: Abyrne at: 6/18/2009 3:49 PM (3 Replies)

Rating (0)

Thanks 2

4 Entries

6/18/2009 3:49 PM	Rate (0)
Abyrne Bronze Member Joined: 11/26/2008 Last visit: 3/8/2023 Posts: 101 Rating: (4)	*Problem solved Hi, I am looking to set up an application using a Sinaut micro, an S7-200 and a Sentron PAC energy meter. (Either PAC3200 or PAC4200 see attached). I want to take the information (values for voltage, current, power values, frequency, power factor etc.) from the PAC meter and transfer it over GSM/GPRS to a control station. Does anyone have any experience or information on a similar configuration? I am looking for the most cost effective solution. I am also looking for information on data transfer rates and communication/network configurations between these meters the PLC and the Sinaut equipment. Any help or information is appreciated! Attachment Sentron PAC meter1.zip (78 Downloads)
	Last edited by: Abyrne at: 8/6/2009 1:10 PM
Suggestion To thank Quote Answer

6/18/2009 7:07 PM	Rate (0)
Darius Platinum Member Joined: 9/28/2005 Last visit: 12/27/2022 Posts: 2957 Rating: (241)	Hello, If your meter is with Profibus-DP communication module then you can't use it in conjunction with S7-22x. You need Profibus-DP master for polling data from slaves (PAC3200). S7-22x can only be Profibus-DP slave. You must have PAC3200 with modbus module to use with S7-22x. Then you simply buy modbus master library for S7-22x and acquire values from PAC3200 via modbus and store it in CPU memory. Then you should be able to read this memoty with SINAUT MICRO-SC
	Last edited by: Darius at: 6/18/2009 7:11 PM Best regards, Darius
Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users Abyrne

6/19/2009 5:12 PM	Rate (0)
Abyrne Bronze Member Joined: 11/26/2008 Last visit: 3/8/2023 Posts: 101 Rating: (4)	Thanks for the reply Darius, Would you have any information about the connection between the modbus module and the PLC... such as what cables are used and data transfer rates?Or any information on service provider SIM card options for data streaming from a MD-720-3 modem? Again any help is much appreciated

Suggestion To thank Quote Answer

6/19/2009 8:35 PM	Rate (0)
Darius Platinum Member Joined: 9/28/2005 Last visit: 12/27/2022 Posts: 2957 Rating: (241)	Abyrne Would you have any information about the connection between the modbus module and the PLC... such as what cables are used and data transfer rates? Modbus module is simply modbus library that can be ordered with order number 6ES7830-2BC00-0YX0. When you buy this library from Siemens then you'll get all information about programming modbus master in S7-22x PLC. You can use the same cables as for Profibu-DP or any RS-485 2 wire standard cable. The same is for connectors. Data transfer rates depends on distance. There are tables with distances and baudrates, but you can use folowing formula to calculate max length of cable at specified baudrate: Length in m = 1200 / ( 1 + ( Baud-rate / 250 )² )^0.5 Abyrne Or any information on service provider SIM card options for data streaming from a MD-720-3 modem? Every different country has different GSM providers with different options. Basically your GSM provider must provide you possibility of data call (CSD protocol).
	Last edited by: Darius at: 6/19/2009 8:36 PM Best regards, Darius
Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users Abyrne

|

Share this page:

Share this page on...

Follow us on