Skip to Content

Register Login

Industry Online Support

Technical Forum

Navigation

Start the engine at a constant speed

Created by: AutoGen_7296539 at: 6/23/2021 7:30 PM (10 Replies)

Rating (1)

Thanks 0

Result pages:: |; 1 | 2; |

11 Entries

Entries per page: 10 | all

6/23/2021 7:30 PM	Rate (0)
AutoGen_7296539 Member Joined: 6/12/2021 Last visit: 2/9/2023 Posts: 15 Rating: (0)	pfuser Hi. This addition to the previous. FC: CALL "SIMODRIVE_CONTROL" , "Z1DB" NR_ACHS_DB :=72 LADDR :=256 WR_PZD :=P#DB72.DBX166.0 BYTE 20 RD_PZD :=P#DB72.DBX206.0 BYTE 20 enable_SFC_PZD:=TRUE Initial UDT30008 address = 156 Write: 156+10 = 166 Read: 156+50 = 206 Best regards. Hi Please guide me so that I can implement this example by Simodrive. I want to start the engine at a constant speed Like the example I sent you in the photo ------------------------------------------------------------------------------------------ Split from How to control Simodrive 611u using profibus. Attachment 20210623_213549.jpg (289 Downloads)
	Last edited by: Jen_Moderator at: 06/24/2021 08:51:45 New subject after splitting
Suggestion To thank Quote Answer

6/23/2021 7:31 PM	Rate (0)
AutoGen_7296539 Member Joined: 6/12/2021 Last visit: 2/9/2023 Posts: 15 Rating: (0)	AutoGen_7296539 pfuser Hi. This addition to the previous. FC: CALL "SIMODRIVE_CONTROL" , "Z1DB" NR_ACHS_DB :=72 LADDR :=256 WR_PZD :=P#DB72.DBX166.0 BYTE 20 RD_PZD :=P#DB72.DBX206.0 BYTE 20 enable_SFC_PZD:=TRUE Initial UDT30008 address = 156 Write: 156+10 = 166 Read: 156+50 = 206 Best regards. Hi Please guide me so that I can implement this example by Simodrive. I want to start the engine at a constant speed Like the example I sent you in the photo Attachment 20210623_213632.jpg (215 Downloads)

Suggestion To thank Quote Answer

6/23/2021 7:32 PM	Rate (0)
AutoGen_7296539 Member Joined: 6/12/2021 Last visit: 2/9/2023 Posts: 15 Rating: (0)	AutoGen_7296539 AutoGen_7296539 pfuser Hi. This addition to the previous. FC: CALL "SIMODRIVE_CONTROL" , "Z1DB" NR_ACHS_DB :=72 LADDR :=256 WR_PZD :=P#DB72.DBX166.0 BYTE 20 RD_PZD :=P#DB72.DBX206.0 BYTE 20 enable_SFC_PZD:=TRUE Initial UDT30008 address = 156 Write: 156+10 = 166 Read: 156+50 = 206 Best regards. Hi Please guide me so that I can implement this example by Simodrive. I want to start the engine at a constant speed Like the example I sent you in the photo Attachment 20210623_214130.jpg (209 Downloads)

Suggestion To thank Quote Answer

6/23/2021 7:33 PM	Rate (0)
AutoGen_7296539 Member Joined: 6/12/2021 Last visit: 2/9/2023 Posts: 15 Rating: (0)	AutoGen_7296539 AutoGen_7296539 AutoGen_7296539 pfuser Hi. This addition to the previous. FC: CALL "SIMODRIVE_CONTROL" , "Z1DB" NR_ACHS_DB :=72 LADDR :=256 WR_PZD :=P#DB72.DBX166.0 BYTE 20 RD_PZD :=P#DB72.DBX206.0 BYTE 20 enable_SFC_PZD:=TRUE Initial UDT30008 address = 156 Write: 156+10 = 166 Read: 156+50 = 206 Best regards. Hi Please guide me so that I can implement this example by Simodrive. I want to start the engine at a constant speed Like the example I sent you in the photo Attachment 20210623_214422.jpg (268 Downloads)

Suggestion To thank Quote Answer

6/24/2021 10:31 AM	Rate (0)
PISCEAN 2010 Diamond Expert Joined: 4/23/2010 Last visit: 4/1/2023 Posts: 8026 Rating: (855)	Hello, What problem you face in commissioning? Please check your hardware project & confirm if you have selected correct 611U drive. In your project selected is SIMODRIVE MC POSMO? Is it correct? What is application? Which is motor? Have you confirmed motor & encoder compatibility with drive? Have you configured drive parameters correctly? e.g. profibus address, telegram type PPO, etc. etc. Please check above points.

Suggestion To thank Quote Answer

6/24/2021 11:28 AM	Rate (0)
AutoGen_7296539 Member Joined: 6/12/2021 Last visit: 2/9/2023 Posts: 15 Rating: (0)	Hi Hello I want to start a 1ft6062 engine. I used the ppo5 method. I want the engine to spin at a constant speed according to the example I am sending you. I want to issue commands for the engine through Profibus. 317 2DP cpu is used I do not have any fault bus fault system I also went online with Simodrive and entered the engine specifications. Only in plc I can not send the command to rotate the motor. Please guide me Best regaurds Attachment 20210623_213632.jpg (228 Downloads)
	Last edited by: AutoGen_7296539 at: 06/24/2021 11:28:48 Last edited by: Jen_Moderator at: 06/24/2021 12:26:37 Edited text for better reading.
Suggestion To thank Quote Answer

6/24/2021 11:30 AM	Rate (0)
AutoGen_7296539 Member Joined: 6/12/2021 Last visit: 2/9/2023 Posts: 15 Rating: (0)	Attachment 20210623_213549.jpg (211 Downloads)

Suggestion To thank Quote Answer

6/24/2021 11:32 AM	Rate (0)
AutoGen_7296539 Member Joined: 6/12/2021 Last visit: 2/9/2023 Posts: 15 Rating: (0)	Attachment 20210623_214422.jpg (244 Downloads)

Suggestion To thank Quote Answer

6/24/2021 11:33 AM	Rate (0)
AutoGen_7296539 Member Joined: 6/12/2021 Last visit: 2/9/2023 Posts: 15 Rating: (0)	Attachment 20210623_214130.jpg (227 Downloads)

Suggestion To thank Quote Answer

6/24/2021 12:06 PM	Rate (1)
PISCEAN 2010 Diamond Expert Joined: 4/23/2010 Last visit: 4/1/2023 Posts: 8026 Rating: (855)	Hello, I understood your question. Please check PLC hardware project for drive address (you attached snap shot). Is it OK? Is control module MLFB correct? Have you set Profibus address correct in drive? Do you have Simocom U software? Can you go on line with drive & check control word & status word? This is what I am suggesting you to check. Unless & until you confirm above points, no one can guide you remotely. HTH

Suggestion To thank Quote Answer

|

Share this page:

Share this page on...

Follow us on