Skip to Content

Register Login

Industry Online Support

Technical Forum

Navigation

STEP7 : Read data from ATV630

Created by: anton.narbut at: 8/3/2018 1:04 PM (5 Replies)

Rating (0)

Thanks 0

6 Entries

8/3/2018 1:04 PM	Rate (0)
anton.narbut Experienced Member Joined: 1/18/2017 Last visit: 5/10/2023 Posts: 52 Rating: (1)	Hi all! Cannot access data from frequency variator ATV630 (with Profibus DP VW3A3607 card). ATV630 is accessible via DP network, which means that its network settings GSD-file are correct. On the drive side PPO profile is set to 101 (Telegram 101). Telegram 101 is configured in HWConfig with required parameter addresses. When I monitor peripheral addresses online I don't see any data (status word, speed etc. is zero) What might be the problem?

Suggestion To thank Quote Answer

8/3/2018 1:23 PM	Rate (0)
PISCEAN 2010 Diamond Member Joined: 4/23/2010 Last visit: 5/7/2023 Posts: 8034 Rating: (855)	anton.narbut Hi all! Cannot access data from frequency variator ATV630 (with Profibus DP VW3A3607 card). When I monitor peripheral addresses online I don't see any data (status word, speed etc. is zero) What might be the problem? How are you accessing data? Is data type correctly addressed while reading data from slave? Have you configured correct address of drive? Please check.

Suggestion To thank Quote Answer

8/3/2018 2:11 PM	Rate (0)
anton.narbut Experienced Member Joined: 1/18/2017 Last visit: 5/10/2023 Posts: 52 Rating: (1)	As I said in my initial post, I have reasons to believe that my problem is not network-related but more config-related. And the question is: what else do I need to configure in HWConfig and on the drive side to get data from it? I plan to access data with SFC14/15. Right now I monitor peripheral addresses of the drive in HWConfig just to check if any data is available. PISCEAN 2010 anton.narbut Hi all! Cannot access data from frequency variator ATV630 (with Profibus DP VW3A3607 card). When I monitor peripheral addresses online I don't see any data (status word, speed etc. is zero) What might be the problem? How are you accessing data? Is data type correctly addressed while reading data from slave? Have you configured correct address of drive? Please check.

Suggestion To thank Quote Answer

6/26/2021 10:58 AM	Rate (0)
ed112233 Posts: 1 Rating: (0)	Siemens' DP is different from Schneider's DP Attachment S.jpg (122 Downloads)
ed112233 Posts: 1 Rating: (0)	Last edited by: Jen_Moderator at: 06/28/2021 10:10:00 New subject after splitting Last edited by: Jen_Moderator at: 06/28/2021 14:39:55 Removed splitting-remark.
Suggestion To thank Quote Answer

6/27/2021 4:29 AM	Rate (0)
fabiogamba Posts: 1 Rating: (0)	Can you be more specific about the differences between Siemens and Schneider's DP?
fabiogamba Posts: 1 Rating: (0)	Last edited by: Jen_Moderator at: 06/28/2021 10:14:32 Edited text for better reading.
Suggestion To thank Quote Answer

6/28/2021 2:25 PM	Rate (0)
Duris_I Diamond Member Joined: 4/28/2015 Last visit: 5/27/2023 Posts: 9511 Rating: (744)	Hello, ed112233 Siemens' DP is different from Schneider's DP ------------------------------------------------------------------------------------------ Split from STEP7 : Read data from ATV630. very sry, your post has no valuable information to Community.
	With best regards... Ivan Duris VId: OMICO
Suggestion To thank Quote Answer

|

Share this page:

Share this page on...

Follow us on