Skip to Content

Register Login

Industry Online Support

Technical Forum

Navigation

STL for S7-1500

Created by: Berg at: 8/22/2013 4:28 AM (11 Replies)

Rating (0)

Thanks 4

Result pages:: |; 1 | 2; |

12 Entries

Entries per page: 10 | all

8/22/2013 4:28 AM	Rate (0)
Berg Silver Member Joined: 1/17/2006 Last visit: 12/26/2022 Posts: 549 Rating: (29)	Hi. What's the equivalent code for S7-1500 of the following code in S7-300 (STEP7 V5.5) in STL ? STEP7 V5.5: L MW0 //integer L 2 *I SLW 3 LAR1 L MW10 //integer OPN DB10 T DW[AR1,P#0.0] //integer Regards.
	"Educate the children and it won't be necessary to punish the men." Pythagoras
Suggestion To thank Quote Answer

8/23/2013 12:07 PM	Rate (0)
Denilson Pegaia Platinum Expert Joined: 9/23/2005 Last visit: 2/3/2023 Posts: 4178 Rating: (1324)	Hi Berg, I don't test you code, but I suppouse that if you post it, it is because there is something wrong... So, how about it?: L MW0 //integer L 2 *I SLW 3 T MD10 L MW10 //integer OPN DB10 T DBW[MD10]
	Denilson Pegaia Siemens Industry Sector Technical Support
Suggestion To thank Quote Answer

8/23/2013 6:14 PM	Rate (0)
Berg Silver Member Joined: 1/17/2006 Last visit: 12/26/2022 Posts: 549 Rating: (29)	Pegaia Hi Berg, I don't test you code, but I suppouse that if you post it, it is because there is something wrong... So, how about it?: L MW0 //integer L 2 *I SLW 3 T MD10 L MW10 //integer OPN DB10 T DBW[MD10] Hi Pegaia. The instructions AR1 and OPN are not accepted in TIA. So, how to convert the code that I posted to TIA Portal in STL. This is my question... Best regards.
	"Educate the children and it won't be necessary to punish the men." Pythagoras
Suggestion To thank Quote Answer

8/23/2013 8:33 PM	Rate (0)
hdhosseini Diamond Expert Joined: 1/28/2009 Last visit: 12/28/2022 Posts: 6785 Rating: (1336)	Hi Pegaia. The instructions AR1 and OPN are not accepted in TIA. So, how to convert the code that I posted to TIA Portal in STL. This is my question... Hello, Have your tested those instructions in the editor? Try the followings for an S7-1500 and compile it.DB1 contains an array of 10 cells - real data type. [code] OPN "Data_block_1" //DB1 LAR1 P#0.0 L 5 lp: T #lp L 100.0 T DBD [ AR1 , P#0.0 ] +AR1 P#4.0 L #lp LOOP lp[/code] Best regards Hamid Hosseini
	Last edited by: hdhosseini at: 8/23/2013 8:42 PM Demo Channel on Youtube
Suggestion To thank Quote Answer

8/23/2013 8:51 PM	Rate (0)
Berg Silver Member Joined: 1/17/2006 Last visit: 12/26/2022 Posts: 549 Rating: (29)	hdhosseini Hi Pegaia. The instructions AR1 and OPN are not accepted in TIA. So, how to convert the code that I posted to TIA Portal in STL. This is my question... Hello, Have your tested those instructions in the editor? Try the followings for an S7-1500 and compile it.DB1 contains an array of 10 cells - real data type. OPN "Data_block_1" //DB1 LAR1 P#0.0 L 5 lp: T #lp L 100.0 T DBD [ AR1 , P#0.0 ] +AR1 P#4.0 L #lp LOOP lp Best regards Hamid Hosseini Hi. The instructions OPN and AR1 are not accepted. OPN "Data_block_1" T DBD [ AR1 , P#0.0 ]
	"Educate the children and it won't be necessary to punish the men." Pythagoras
Suggestion To thank Quote Answer

8/23/2013 8:56 PM	Rate (0)
hdhosseini Diamond Expert Joined: 1/28/2009 Last visit: 12/28/2022 Posts: 6785 Rating: (1336)	As I have tested with success, I should ask you which version of program using and also providing some snapshots of error generated while typing instructions or while compiling.
	Demo Channel on Youtube
Suggestion To thank Quote Answer

8/23/2013 10:18 PM	Rate (0)
Denilson Pegaia Platinum Expert Joined: 9/23/2005 Last visit: 2/3/2023 Posts: 4178 Rating: (1324)	TIP: Use DB with absolute address (non optimized).
	Denilson Pegaia Siemens Industry Sector Technical Support
Suggestion To thank Quote Answer
This contribution was helpful to 2 thankful Users Berg hdhosseini

8/23/2013 10:24 PM	Rate (0)
hdhosseini Diamond Expert Joined: 1/28/2009 Last visit: 12/28/2022 Posts: 6785 Rating: (1336)	Pegaia TIP: Use DB with absolute address (non optimized). Same in my test.
	Demo Channel on Youtube
Suggestion To thank Quote Answer

8/23/2013 10:55 PM	Rate (0)
Berg Silver Member Joined: 1/17/2006 Last visit: 12/26/2022 Posts: 549 Rating: (29)	Pegaia TIP: Use DB with absolute address (non optimized). Hi. Where can I select this option in TIA V12 ? When I create a new DB this option is not available for me on the screen... I can only choose between FB, FC, OB, etc.. There isn't a check box with this option. thanks.
	"Educate the children and it won't be necessary to punish the men." Pythagoras
Suggestion To thank Quote Answer

8/23/2013 11:05 PM	Rate (0)
hdhosseini Diamond Expert Joined: 1/28/2009 Last visit: 12/28/2022 Posts: 6785 Rating: (1336)	For TIA V12, that is available in properties of a DB(Right click on DB-->Properties-->attribute--> Optimied block access. But before un-check read the following: Setting up block access STEP 7 Professional V12.0 (01/2013, English) wrote: Procedure To set the block access, proceed as follows: Open the "Program blocks" folder in the project tree. Right-click on the block whose block access you want to change. Select the "Properties" command in the shortcut menu. The properties dialog box of the block opens. Click "Attributes" in the area navigation. Enable or disable the "Optimized block access" option. Confirm your entries with "OK". What differences should you watch out for between optimized data storage and the standard type of block access in STEP 7 (TIA Portal) V12?
	Demo Channel on Youtube
Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users Berg

|

Share this page:

Share this page on...

Follow us on