Skip to Content

Register Login

Industry Online Support

Technical Forum

Navigation

TIA V13, error after compile

Created by: heineken04 at: 1/27/2016 12:32 PM (19 Replies)

Rating (0)

Thanks 2

Result pages:: |; 1 | 2; |

20 Entries

Entries per page: 10 | all

1/28/2016 12:20 PM	Rate (0)
heineken04 Regular Member Joined: 12/14/2015 Last visit: 6/10/2016 Posts: 25 Rating: (0)	ok, but if i set on move block value 20 on input, it will be 20 on the output? it doesn't metter that a selected that output to a voltage 0-10 ? what voltage will be on my output?
	Last edited by: heineken04 at: 1/28/2016 12:25:39 PM
Suggestion To thank Quote Answer

1/28/2016 12:37 PM	Rate (0)
heineken04 Regular Member Joined: 12/14/2015 Last visit: 6/10/2016 Posts: 25 Rating: (0)	how can i know what voltage will be in output if i set it for example on 300?

Suggestion To thank Quote Answer

1/28/2016 12:40 PM	Rate (0)
Duris_I Diamond Member Joined: 4/28/2015 Last visit: 10/30/2024 Posts: 10585 Rating: (825)	Hello, pls look, we don't know what range of values you want put between 0-10V. Analog Output value is from 0 to 27648, but it depends how you set configuration on analog card. If you select range of measurement between -10 .. +10V, then that range (0-27648) will be -10V..0 and +10..27648. Edit: Pozdravujem... Edit2: To know exactly what Voltage can be on output, simply meassure it with multimeter on card.
	Last edited by: Duris_I at: 1/28/2016 12:43:01 PM Last edited by: Duris_I at: 1/28/2016 12:45:45 PM With best regards... Ivan Duris Flight: OMICO
Suggestion To thank Quote Answer

1/28/2016 1:03 PM	Rate (0)
heineken04 Regular Member Joined: 12/14/2015 Last visit: 6/10/2016 Posts: 25 Rating: (0)	Thank you. I have one more question, i have no errors or warning, but my analog output module is in SF mode all the time... what is the problem

Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users Duris_I

1/28/2016 1:16 PM	Rate (0)
Duris_I Diamond Member Joined: 4/28/2015 Last visit: 10/30/2024 Posts: 10585 Rating: (825)	Hello, probably you need connect some power source connection to module, L+ (24V) and M like needed in cover pictures. Edit: pls look carefuly in cover back side, if module needs this.
	Last edited by: Duris_I at: 1/28/2016 1:18:59 PM With best regards... Ivan Duris Flight: OMICO
Suggestion To thank Quote Answer

1/28/2016 1:27 PM	Rate (0)
heineken04 Regular Member Joined: 12/14/2015 Last visit: 6/10/2016 Posts: 25 Rating: (0)	power source is connected correctly, SF led starts red in the momment i connect back connector. is it possible that something is wrong with AO module ? I set AO through tia portal on some value, but when i measure it, it it 0 volts. and module is in SF mode.

Suggestion To thank Quote Answer

1/28/2016 1:34 PM	Rate (0)
Duris_I Diamond Member Joined: 4/28/2015 Last visit: 10/30/2024 Posts: 10585 Rating: (825)	Sry, really don't understand what are your steps - SF light up when I put back connector. You mean while PLC is ON, you putting card IN/OUT????
	With best regards... Ivan Duris Flight: OMICO
Suggestion To thank Quote Answer

1/28/2016 1:41 PM	Rate (0)
heineken04 Regular Member Joined: 12/14/2015 Last visit: 6/10/2016 Posts: 25 Rating: (0)	yes , put i first connected AO module when the PLC was off. But SF led on AO module is always on

Suggestion To thank Quote Answer

1/28/2016 1:52 PM	Rate (0)
Duris_I Diamond Member Joined: 4/28/2015 Last visit: 10/30/2024 Posts: 10585 Rating: (825)	hmmm pls have you right configuration? Is that AO card order number correctly added to HW cfg? This looks like wrong HW configuration in this case... Edit: question, why you don't use AO on CPU313C? Aren't enough?
	Last edited by: Duris_I at: 1/28/2016 1:59:41 PM With best regards... Ivan Duris Flight: OMICO
Suggestion To thank Quote Answer

1/28/2016 2:53 PM	Rate (0)
heineken04 Regular Member Joined: 12/14/2015 Last visit: 6/10/2016 Posts: 25 Rating: (0)	i wanted to use this module, but because a dont know how, i will use AO on CPU. Thank you. !!!

Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users Duris_I

|

Share this page:

Share this page on...

Follow us on