Skip to Content

Register Login

Industry Online Support

Technical Forum

Navigation

TIP: How to convert a V11 project to V12

Created by: Denilson Pegaia at: 3/4/2013 7:44 PM (19 Replies)

Rating (1)

Thanks 7

Result pages:: |; 1 | 2; |

20 Entries

Entries per page: 10 | all

3/4/2013 7:44 PM	Rate (1)
Denilson Pegaia Platinum Expert Joined: 9/23/2005 Last visit: 6/7/2023 Posts: 4184 Rating: (1342)	Hi, the main steps are: 1 - Open STEP 7 V12 2 - Open the V11 project (Menu: Project->Open) 3 - Upgrade the project (Menu: Project->Upgrade) The STE7 will perform a conversion and save the new project as name_V12 in a different directory. After that the user should compile PLC's hw and sw before use.
	Denilson Pegaia Siemens Industry Sector Technical Support
Suggestion To thank Quote Answer
This contribution was helpful to 7 thankful Users Tomy Master Carona AutoGen_360917 gdglisch82 C-3PO vladimnick zykik

3/26/2013 9:08 AM	Rate (0)
cihangarip Experienced Member Joined: 6/9/2012 Last visit: 2/25/2023 Posts: 32 Rating: (0)	Hello I converted the project as telling de 0xc000af0d00008005 above I get an error in the form. How can I fix this problem do you think. Thank you for your interest. Best Regards Cihan GARIP

Suggestion To thank Quote Answer

3/26/2013 11:19 AM	Rate (0)
Denilson Pegaia Platinum Expert Joined: 9/23/2005 Last visit: 6/7/2023 Posts: 4184 Rating: (1342)	Hi, it very difficult to determine what happens. Maybe, your v11 project was already corrupted. I suggest you open a Support Request. So the experts could take a look at your project. At and, I ask you to post here what they said.
	Denilson Pegaia Siemens Industry Sector Technical Support
Suggestion To thank Quote Answer

4/23/2013 10:36 PM	Rate (0)
JC1138 Member Joined: 6/8/2010 Last visit: 3/23/2023 Posts: 1 Rating: (0)	I am having the same issue. I tried to follow your 3 step method, but my screen does not show 'upgrade', but it shows 'migrate'.....any further tips. please?

Suggestion To thank Quote Answer

9/2/2013 7:52 PM	Rate (0)
iess2600 Posts: 5 Rating: (0)	Same happens to me, I can't see the "Upgrade" option, and if I choose "Migrate Project..." it can't find my .ap11 file.
iess2600 Posts: 5 Rating: (0)
Suggestion To thank Quote Answer

9/3/2013 12:40 PM	Rate (0)
Denilson Pegaia Platinum Expert Joined: 9/23/2005 Last visit: 6/7/2023 Posts: 4184 Rating: (1342)	Hi, migrate is used for non TIA softwares (WinCC flexible STEP 7 V5). It is necessary first o open (with open command) a V11 project. Just after that the option "upgrade" will be enabled.
	Denilson Pegaia Siemens Industry Sector Technical Support
Suggestion To thank Quote Answer

11/1/2013 10:34 AM	Rate (0)
tk19 Posts: 59 Rating: (0)	Dear All, as per Mr. Pegaie, i have open the project in V11 also the same time i have open V12 Software, But still i Update Not enable..it only shows Migrate Buttons...Please tell me what i do...bcoz due to that i m in trouble...
tk19 Posts: 59 Rating: (0)
Suggestion To thank Quote Answer

11/12/2013 12:28 PM	Rate (0)
HansAST Experienced Member Joined: 5/24/2009 Last visit: 4/20/2023 Posts: 90 Rating: (3)	You need to open the V11 project with Tia Portal V12...

Suggestion To thank Quote Answer

1/9/2014 3:13 AM	Rate (0)
mflima Bronze Member Joined: 1/24/2008 Last visit: 5/16/2023 Posts: 30 Rating: (1)	Hi, I have a V11 project and I tried to upgrade it to the V12 version using the TIA V12 SP1 Update 3. I followed the 3 steps method described in the first post of this thread but near the end (about 75% of processing) the TIA portal opens a small window titled (0080:000030) telling me the following message: An error occurred while upgrading the project. The small window shows a link to a log File. Unfortunately the log file doesn’t give any significant information. The content of the log file is: Message Time Upgrade started 1/9/2014 1:44:17 AM Reading information from previous project 1/9/2014 1:44:17 AM Updating new project 1/9/2014 1:44:27 AM Updating new project 1/9/2014 1:44:41 AM To finish upgrade of the project, select the menu command "Edit > Compile" for each device in the project. 1/9/2014 1:45:27 AM Upgrade failed. 1/9/2014 1:45:34 AM After the first small window appears other titled (0080:000041) telling me the following message: Upgrade failed. Can you help me? MLima

Suggestion To thank Quote Answer

1/9/2014 10:06 AM	Rate (0)
Denilson Pegaia Platinum Expert Joined: 9/23/2005 Last visit: 6/7/2023 Posts: 4184 Rating: (1342)	Hi, My suggestions: 1 - First of all, delete (Windows Explorer) the contends of IM folder (ATENTION delete the contends, not the folder. After that try to open and convert in V12. 2 - Open the project. Open the STEP7 twice. In new instance of STEP7 create or open a new V11 project. Select all devices on Networkview (from first instance of firstSTEP7) and paste in the new project (second STEP7 instance). Save the new project and close all STEP7. After that try to open and convert in V12. 3 - The project maybe is corrupt. Open a Support Request, relate the problem and send the project to be analised.
	Denilson Pegaia Siemens Industry Sector Technical Support
Suggestion To thank Quote Answer

|

Share this page:

Share this page on...

Follow us on