Skip to Content

Register Login

Industry Online Support

Technical Forum

Navigation

TM 1703 ACP - IEC 60870-5-101 Master

Created by: phamlamth at: 1/3/2012 7:36 PM (14 Replies)

Rating (1)

Thanks 2

Result pages:: |; 1 | 2; |

15 Entries

Entries per page: 10 | all

1/6/2012 3:58 PM	Rate (0)
phamlamth Regular Member Joined: 1/3/2012 Last visit: 1/10/2025 Posts: 10 Rating: (0)	Hi Ensar, I think your capture image show a lot to me, I didnt pay enough attention to topology setting, but now I think - absolutely think this setting can solve my problem. Even I still not upload parameter yet! The RTU send IEC 101 to TM is RTU32 of Brodersen:http://brodersensystems.com/products/plcrtu-series/rtu32/ I will take my chance and tell you the result later. But do you have any comment on Diagnostic file I sent to you? It's show that Master 101 got communication error with its station, but I still can get the data from RTU32 and can use send command to it? What does this error mean? Anyway, thank you alot for your help! Lam Pham

Suggestion To thank Quote Answer

1/6/2012 4:55 PM	Rate (0)
ensark2 Bronze Member Joined: 11/18/2009 Last visit: 12/12/2024 Posts: 263 Rating: (18)	Hi Lam Pham, I have looked at diagnostic file. I think this message you will not get this again. Error_bit 12: Remote station did not acknowledge GA ....... Try this with topology I think it will be solved. Best Regards Ensar

Suggestion To thank Quote Answer

1/6/2012 5:10 PM	Rate (0)
phamlamth Regular Member Joined: 1/3/2012 Last visit: 1/10/2025 Posts: 10 Rating: (0)	Hi Ensar, Yeah, you're right about this GI topology will effect to that Error bit. But I just want to ask about the "K section: Communication error" of UMPMA0. It's said there's acknowledgement error when connect TM1703 to RTU. And I still wonder that if there's error, why I can still get the data and control RTU through TM1703! I was change in topology at IEC 60870 column, from 1703 profile to IEC profile. Hopefully it could give me something. Thank you once again! Lam Pham

Suggestion To thank Quote Answer

1/6/2012 6:30 PM	Rate (0)
ensark2 Bronze Member Joined: 11/18/2009 Last visit: 12/12/2024 Posts: 263 Rating: (18)	Hi Lam Pham, I dont think you will get anything by changing to IEC profile. I have tried this before. Acknowledgement error is because slave does not sent Acknowledgment that it has received GI. It just sends data after acknowledgement. I cant remember if it is possible to turn this off. You should check in system technique under communication. There where you have PRE0, PRE1, PRE2, PRE3. Did you acknowledge network before opening diagnostic? This error will not do any harm. I have had this before. Have you tried this with topology? Regards Ensar
	Last edited by: ensark2 at: 1/6/2012 6:30 PM
Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users fanana

10/17/2017 8:49 PM	Rate (0)
AutoGen_682172 Posts: 13 Rating: (0)	Sir/Madam if u have copy of database file for TM1703 for SM2541 (umps00) IEC101 slave /Master protocol, pls send configuration file TM1703 for my reference regrds Siva
AutoGen_682172 Posts: 13 Rating: (0)
Suggestion To thank Quote Answer

|

Share this page:

Share this page on...

Related topics by keywords:

Follow us on