Skip to Content

Register Login

Industry Online Support

Technical Forum

Navigation

TS-Adapter IE - access to a MP 277

Created by: Vagabund at: 11/13/2008 1:13 PM (7 Replies)

Rating (0)

Thanks 0

8 Entries

11/13/2008 1:13 PM	Rate (0)
Vagabund Advanced Member Joined: 11/5/2008 Last visit: 7/20/2011 Posts: 64 Rating: (1)	Hi people. I´ve a new question about TS-Adapter IE... The new problem: 22778621 Itriedto dothis example to access a MP 277 using TS-Adapter IE, I see the TS-Adapter IP, but I can´t see the MP IP direction.
	Last edited by: CS Moderator at: 11/14/2008 1:02 PM new subject after splitting
Suggestion To thank Quote Answer

11/13/2008 3:37 PM	Rate (0)
J_Bell Posts: 5822 Rating: (412)	Dear Vagabund, is it this FAQ you talk about? Which settings do you have to make so that a ProTool project or WinCC flexible project can be transferred via TeleService Adapter IE? If yes, what do you mean by "the MP IP direction"? Best regards J_Bell
J_Bell Posts: 5822 Rating: (412)
Suggestion To thank Quote Answer

11/13/2008 4:04 PM	Rate (0)
Vagabund Advanced Member Joined: 11/5/2008 Last visit: 7/20/2011 Posts: 64 Rating: (1)	This is the FAQ. The problem is: I can see TS-Adapter using analog modem, I can connect, and after, I use the internet explorer and I can see the web page of TS-Adapter. I proceed like the FAQ, but the MP277 don´t appears in my net.

Suggestion To thank Quote Answer

11/13/2008 4:48 PM	Rate (0)
J_Bell Posts: 5822 Rating: (412)	Dear Vagabund, if you configured everything as you said it and you configured the S7-Communication you should be able to see all nodes, if you are connected by the TELESERVICE Software to the TS Adapter IE and you opened STEP7. Available nodes should show you now all nodes connected to the network the TS-Adaptor IE is connected to. Do you have, besides the Switch you are connected to, any other S7 nodes in the network, maybe a PLC CPU? I hope so because than you should be able to see it now. Best regards J_Bell
J_Bell Posts: 5822 Rating: (412)
Suggestion To thank Quote Answer

11/17/2008 5:38 PM	Rate (0)
Vagabund Advanced Member Joined: 11/5/2008 Last visit: 7/20/2011 Posts: 64 Rating: (1)	Hi J_Bell: I configuring my net, and I try to find the Multi Panel 277, but I can´t see the IP direction, I only see the TS-Adapter IE. (I use Step 7, Internet Explorer, win CC...) Any suggestion??, it´s really complicated, I need help. I include a 319 PN/DP CPU in my installation, didn´t appears.
	Last edited by: Vagabund at: 11/17/2008 6:00 PM
Suggestion To thank Quote Answer

11/17/2008 11:05 PM	Rate (0)
J_Bell Posts: 5822 Rating: (412)	Dear Vagabound, I fear your do not access the Network of the PLC, Panel and TS Adaptor II right, there must be something wrong. Would you please check for example if you have another NIC in your PC that uses the same Network ID as the Network ID of this PLC Network? Did you try the diagnostics of TELESERVICE Software yet? Just to see if the IP you received by the Adaptor while you entered the network is the one you configured. If needed it might be possible to try to connect to your network, if you contact the International Custumer Support. Best regards J_Bell
J_Bell Posts: 5822 Rating: (412)
Suggestion To thank Quote Answer

11/18/2008 10:28 AM	Rate (0)
Vagabund Advanced Member Joined: 11/5/2008 Last visit: 7/20/2011 Posts: 64 Rating: (1)	Hi J_Bell EUREKA!!! It´s runing!!! Thanks for your time. Thanks for your help.

Suggestion To thank Quote Answer

11/18/2008 10:57 AM	Rate (0)
J_Bell Posts: 5822 Rating: (412)	Dear Vagabund, you are welcome.... It is good to know that it works now. Best regards J_Bell
J_Bell Posts: 5822 Rating: (412)
Suggestion To thank Quote Answer

|

Share this page:

Share this page on...

Follow us on