Skip to Content

Register Login

Industry Online Support

Technical Forum

Navigation

update the hardware catalog of your STEP 7 Basic installation

Created by: Tomy Master at: 11/20/2010 5:03 PM (8 Replies)

Rating (2)

Thanks 5

9 Entries

11/20/2010 5:03 PM	Rate (0)
Tomy Master Gold Member Joined: 5/4/2009 Last visit: 11/9/2022 Posts: 906 Rating: (40)	Flomaster Hi! You need to update the hardware catalog of your STEP 7 Basic installation. To do this, download Hardware Support Packages here. Sorry... But how to do the update procedure.... Tomy. Splitted from SM 1231 AI 8x13 bit issue.
	Last edited by: O_Moderator at: 11/22/2010 10:20 AM new subject after splitting Aim Higher
Suggestion To thank Quote Answer

11/22/2010 7:00 AM	Rate (0)
Flomaster Posts: 65 Rating: (2)	Hi! It's very easy. 1. Download HWSP from the link. It is zip archive. 2. Unpack this archive. 3. In unpacked folder find file "Install_HW_add-ons.bat" and run it. Don't forget to close STEP7 Basic before this procedure. 4. Run STEP7 Basic and you will see updated Hardware Catalog.
Flomaster Posts: 65 Rating: (2)
Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users Tranhieu0983

11/22/2010 9:38 AM	Rate (0)
Tomy Master Gold Member Joined: 5/4/2009 Last visit: 11/9/2022 Posts: 906 Rating: (40)	Dear friend... I tried, but it failed, please see attached. Thank you for yoour support. Tomy. Attachment install error.gif (207 Downloads)
	Aim Higher
Suggestion To thank Quote Answer

11/22/2010 9:50 AM	Rate (0)
Wizard Diamond Member Joined: 4/24/2006 Last visit: 2/2/2023 Posts: 8586 Rating: (1122)	Hi, Are you logged in as Administrator? Best regards, Wizard

Suggestion To thank Quote Answer

11/22/2010 10:18 AM	Rate (0)
Tomy Master Gold Member Joined: 5/4/2009 Last visit: 11/9/2022 Posts: 906 Rating: (40)	Dear friend... Yes as adminstrator... Tomy
	Aim Higher
Suggestion To thank Quote Answer

11/22/2010 2:59 PM	Rate (1)
0_Einstein Diamond Expert Joined: 7/7/2010 Last visit: 1/27/2023 Posts: 13080 Rating: (2124)	Maybe try copying the unarchived HSP folder/files to the same hard drive as your S7-1200 software and install from there. I did the HSP updates by placing the HSP files on the desktop, updating, then deleting the HSP files from my desktop.
	science guy
Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users Tomy Master

11/22/2010 7:12 PM	Rate (0)
UMENCHO Diamond Member Joined: 3/21/2006 Last visit: 12/18/2022 Posts: 10221 Rating: (1175)	Hello, And you already have SP2 of 10.5... Best regards, Hristo Mihalev

Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users Tomy Master

11/23/2010 10:15 AM	Rate (1)
TomDeWou Platinum Expert Joined: 11/15/2006 Last visit: 5/7/2021 Posts: 1319 Rating: (167)	Select the bat-File with right mouse click and select 'Run as Administrator' if available. The error message indicates that you are not logged in as an Admin.
	Have Fun! TomDeWou
Suggestion To thank Quote Answer
This contribution was helpful to 2 thankful Users Tomy Master Tranhieu0983

5/16/2012 2:07 PM	Rate (0)
David1981 Experienced Member Joined: 5/3/2012 Last visit: 1/31/2023 Posts: 158 Rating: (2)	Hello, first you excuse me for my bad english, I know pass a lot of time the last post, but, i had equal problem, I executed my hardware catalog update since a external Hard disk, and the update fault, next I copied zip hardware catalog update in the desktop, and update was right. Very Regards, David.

Suggestion To thank Quote Answer

|

Share this page:

Share this page on...

Follow us on