Skip to Content

Register Login

Industry Online Support

Technical Forum

Navigation

WinCC Flexible Advanced 2007 Toolbars Disappeared!

Created by: snk at: 3/18/2008 4:45 PM (10 Replies)

Rating (1)

Thanks 3

Result pages:: |; 1 | 2; |

11 Entries

Entries per page: 10 | all

3/18/2008 4:45 PM	Rate (0)
snk Posts: 5 Rating: (0)	I have installed the software last week, was running fine until today, WHERE ALL OF MY TOOLBARS have disappeared. I cannot seem to get them back visually either. I cannot double click on my objects to bring up their properties manageras well. Is there something that has changed in the settings or something? This is extremely frustrating....
snk Posts: 5 Rating: (0)	Last edited by: snk at: 3/18/2008 4:47 PM
Suggestion To thank Quote Answer

3/18/2008 5:55 PM	Rate (0)
The Brain Gold Member Joined: 10/19/2005 Last visit: 11/30/2020 Posts: 1611 Rating: (121)	Hi, for a long time i have the same problem. I belief,a colleague hadget thisinfo from the customer support. -> see attachment. regards, Attachment Propertiy_Window.zip (855 Downloads)

Suggestion To thank Quote Answer

3/18/2008 8:08 PM	Rate (0)
snk Posts: 5 Rating: (0)	I tried the attached instructions, with no change. I really don't want to have to re-install everything. It took a couple of hours for the whole install, plus I don't even know how it changed to begin with.
snk Posts: 5 Rating: (0)
Suggestion To thank Quote Answer

3/19/2008 8:04 AM	Rate (0)
The Brain Gold Member Joined: 10/19/2005 Last visit: 11/30/2020 Posts: 1611 Rating: (121)	Hi, look under"View". There are a point "Reset Layout" maybe after then it willbe better. If not,call the customer support. regards,

Suggestion To thank Quote Answer

3/20/2008 1:23 PM	Rate (1)
Zenta Silver Member Joined: 10/12/2006 Last visit: 11/5/2024 Posts: 206 Rating: (25)	snk I have installed the software last week, was running fine until today, WHERE ALL OF MY TOOLBARS have disappeared. I cannot seem to get them back visually either. I cannot double click on my objects to bring up their properties manageras well. Is there something that has changed in the settings or something? This is extremely frustrating.... Hi snk, this topic is closed / solved, and here is the solution: "Recreate WinCC flexible Templates and Caches For different reasons it can become necessary to set back WinCC flexible to a defined original status. Reasons for this can be the following: -defective configuration of the surface (Property view no longer visible or incomplete) -defective database-templates The following procedure recreates the database-templates of WinCC flexible and erases the caches: 1. Please close all processes „Hmies.exe“ and „HmiSmartStart.exe“ with the Windows TaskManager. Please do not close the TaskManager. 2. After this please start the following procedure (described below) via START > RUN and copy following line into the command prompt (maybe you must adapt your install path to this command line): "C:\Program Files\Siemens\SIMATIC WinCC flexible\WinCC flexible 2005\Hmies.exe" -reset -new -silentmode true -autoclose true 3. After this you must check the starting of a new task hmies.exe in the TaskManager. 4. After 2-3 min's this task should be closed automatically. Now you can start WinCC flexible again as usual. " Best regards Zenta

Suggestion To thank Quote Answer
This contribution was helpful to 2 thankful Users Dmitrij_Thüringen assokhi

3/20/2008 1:52 PM	Rate (0)
snk Posts: 5 Rating: (0)	Zenta, You solved the problem! How/Why is this happening? I am using Win2K SP4, Dell Latitude D620. It is only this software that is acting up... Is this a software error?
snk Posts: 5 Rating: (0)
Suggestion To thank Quote Answer

3/20/2008 2:22 PM	Rate (0)
Zenta Silver Member Joined: 10/12/2006 Last visit: 11/5/2024 Posts: 206 Rating: (25)	snk Zenta, You solved the problem! How/Why is this happening? I am using Win2K SP4, Dell Latitude D620. It is only this software that is acting up... Is this a software error? Hi snk, I don't know why or how is happening this problem, but this error I have 4 times. First 2 times I make a reinstall, and after that I have had enough. I wrote the SIEMENS and they have sended this method... I think yes it's a little bug in the program... But I think they will try to fix it... Best regards Zenta

Suggestion To thank Quote Answer

3/20/2008 3:30 PM	Rate (0)
snk Posts: 5 Rating: (0)	Thanks again Zenta. I will keep my printout handy....... It more than likely will happen again. Much appreciated. Have a great weekend.
snk Posts: 5 Rating: (0)
Suggestion To thank Quote Answer

3/20/2008 5:17 PM	Rate (0)
Zenta Silver Member Joined: 10/12/2006 Last visit: 11/5/2024 Posts: 206 Rating: (25)	snk Thanks again Zenta. I will keep my printout handy....... It more than likely will happen again. Much appreciated. Have a great weekend. Your welcome and thank you. Best regards Zenta

Suggestion To thank Quote Answer

3/24/2014 9:55 AM	Rate (0)
DanishS Regular Member Joined: 3/19/2014 Last visit: 10/2/2024 Posts: 13 Rating: (0)	Thanks for Solution. But i will add some info for WinCC Flexible 2008 users, After 2-3 miutes HmiES.exe is not stoping automaticaly, I just closed the WinCC and restarted, Its now on its original state. thanks Regards Danish KSA

Suggestion To thank Quote Answer

|

Share this page:

Share this page on...

Follow us on