Skip to Content

Register Login

Industry Online Support

Technical Forum

Navigation

WinCC Flexible and S5 PLC

Created by: ecsiberg at: 5/13/2014 8:48 AM (3 Replies)

Rating (0)

Thanks 1

4 Entries

5/13/2014 8:48 AM	Rate (0)
ecsiberg Advanced Member Joined: 10/25/2005 Last visit: 5/8/2023 Posts: 25 Rating: (1)	If I read the WinCC flexible Communication manual at chapter 7.2 Configuring the communication driver for SIMATIC S5 / 7.2.1.5 KT data type is allowed for AS511 protocol what does it mean ? how can I set an S5 time value in a DW or in a MW in a old S5 PLC (e.g. S5-95U or S5-115U) via WinCC flexible HMI just like OP77B (still for sale) ? if I use KC format - how can I set the time base ? shall I use that fixed in the PLC program ? sound strange don't you agree?
	Last edited by: Blue Moderator at: 13.05.2014 13:36 new subject after splitting from /tf/WW/en/Posts/30168#top
Suggestion To thank Quote Answer

5/13/2014 5:43 PM	Rate (0)
IBN-Service Posts: 8946 Rating: (995)	If you use a S5 connection, you can choose a variable as S5-Time (=KT)in WinCCflex.
IBN-Service Posts: 8946 Rating: (995)
Suggestion To thank Quote Answer

5/13/2014 11:16 PM	Rate (0)
Amit_86 Platinum Member Joined: 3/18/2008 Last visit: 8/25/2022 Posts: 1750 Rating: (270)	ecsiberg If I read the WinCC flexible Communication manual at chapter 7.2 Configuring the communication driver for SIMATIC S5 / 7.2.1.5 KT data type is allowed for AS511 protocol what does it mean ? how can I set an S5 time value in a DW or in a MW in a old S5 PLC (e.g. S5-95U or S5-115U) via WinCC flexible HMI just like OP77B (still for sale) ? if I use KC format - how can I set the time base ? shall I use that fixed in the PLC program ? sound strange don't you agree? Hi, This FAQ might give you some Hint. Entering the time value for the timer
	VANDE MATARAM.....
Suggestion To thank Quote Answer

5/14/2014 1:30 AM	Rate (0)
Abdalkader Posts: 65 Rating: (5)	here is some tips for connecting S5 plc with a wincc flexible HMI panel 1-RS422/TTY adapter 6AV6671-8XJ00-0XA0 must be used with6XV1440 – 2A cable with the attached picture pin assignment 2-Select the “SIMATIC AS 511” driver in the connection setup dialog in wincc. 3-Set the dip switches for RS422/RS485 mode 4- ur communication will be serial , remote off in the transfer settings in the hmi 5-The PLC tags address can be either S5 timer (i.e. “T5”) or a data-word (i.e. “DB 100 DW 10”). The PLC tags Data type must be “KT”. 6-Linear tag scaling must be applied, with “PLC lower value” = 0, “PLC upper value” = 1000, “HMI device lower value” = 0, “HMI device upper value” = 1. best Regards :) Attachment Panels_Anschlussleitungen_Kabelbelegung_01_e.gif (249 Downloads)
Abdalkader Posts: 65 Rating: (5)
Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users Ibrahim Fathy

|

Share this page:

Share this page on...

Follow us on