Skip to Content

SiePortal

The integrated platform for your product selection, buying and support workflow - bringing together Industry Mall and Online Support.

SiePortalDeutsch

Search

Home
Support Support
{{(apiData.Support | filter:{'rank':1}:true)[0].title}} Support
- Menu temporary not available
- Menu temporary not available
- Menue temporary not available
- {{item.title}}

Products & Services
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
Support Support
{{(apiData.Support | filter:{'rank':1}:true)[0].title}} Support
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
MySiePortal MySiePortal
{{(apiData.MySiePortal | filter:{'rank':1}:true)[0].title}} MySiePortal
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
Cart ({{apiData.CartCount}})

Navigation

Encoder wiring diagram

Created by: RetroK at: 10/7/2015 1:02 PM (8 Replies)

Rating (0)

Thanks 1

9 Entries

10/7/2015 1:02 PM	Rate (0)
RetroK Bronze Member Joined: 5/1/2013 Last visit: 8/29/2024 Posts: 428 Rating: (4)	Hello I would like to see the wiring diagram of this connector. And I try to connect to the encoder of the motor 1PH8133-1JF00-0BA1, I would like to know the signal corresponding to each number. Attachment CONNECTOR.PNG (686 Downloads)

Suggestion To thank Quote Answer

10/7/2015 1:28 PM	Rate (0)
ChristophD Grandmaster Joined: 5/12/2006 Last visit: 11/11/2024 Posts: 22444 Rating: (3029)	Hello, the wiring depends not on the Connector , this connector can be used for a lot of encoders. You should show which MLFB is on the cable because with this MLFB you can decode which encoder wiring is used. Or have you only the connector and will wire the cable by yourself? Regards Christoph

Suggestion To thank Quote Answer

10/7/2015 1:55 PM	Rate (0)
RetroK Bronze Member Joined: 5/1/2013 Last visit: 8/29/2024 Posts: 428 Rating: (4)	I do not know what is inside the motor encoder. How can I know? As mentioned above, the motor is the product produced by Siemens. And I would like to know whether each pin number is connected with which wire. To find out, I do Must disassemble the connector?

Suggestion To thank Quote Answer

10/7/2015 2:07 PM	Rate (0)
IBN-Service Posts: 8946 Rating: (999)	how about a tester? Depending form type of Encoder you will find also the pin assignment in Siemens documentation.
IBN-Service Posts: 8946 Rating: (999)
Suggestion To thank Quote Answer

10/7/2015 2:08 PM	Rate (0)
RetroK Bronze Member Joined: 5/1/2013 Last visit: 8/29/2024 Posts: 428 Rating: (4)	It is written as 6FX5002-2AH00-1KA0 the cable connected to the connector.

Suggestion To thank Quote Answer

10/7/2015 2:12 PM	Rate (0)
William_B Posts: 5225 Rating: (1195)	etroK Hello I would like to see the wiring diagram of this connector. And I try to connect to the encoder of the motor 1PH8133-1JF00-0BA1, I would like to know the signal corresponding to each number. One step back please. Where did the cable come from? Was it shipped with the motor or with the drive? Do you need to connect a Siemens motor to Siemens drive or 3rd party drive? Recommend.. If you know which Siemens drive is normally paired with the motor, the documentation of the drive will have details of the pin layout. You may even have some documentation with the motor/cable. I have an example to show my point.. from the V60 drive: (see attached file) Put the part number in the search field and see if there is any information (such as what drive is normally used) that can help you help yourself. Regards & good luck. w Attachment example of pin-outs found in V60 manual.png (1450 Downloads)
William_B Posts: 5225 Rating: (1195)	Last edited by: William_B at: 10/7/2015 2:14:19 PM removed image from text, added via attached PNG
Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users RetroK

10/7/2015 2:17 PM	Rate (0)
William_B Posts: 5225 Rating: (1195)	IBN-Service Depending form type of Encoder you will find also the pin assignment in Siemens documentation. That is very true. You need to know which encoder is used in the motor. The cables/connector however seem to carry all (or most) combinations but only the ones that are used goes through to the drive. (see earlier attached image)
William_B Posts: 5225 Rating: (1195)
Suggestion To thank Quote Answer

10/7/2015 2:27 PM	Rate (0)
ChristophD Grandmaster Joined: 5/12/2006 Last visit: 11/11/2024 Posts: 22444 Rating: (3029)	Hello, if i see this correctly: Cable is for HTL Encoder which build in in the 1PH8 On the other side should be a SUB-D connector for the SMC30 module. This cable ic complety pre-assembled , so why you need the wiring diagram exactly? Regards Christoph Attachment encodersheet.png (930 Downloads)

Suggestion To thank Quote Answer

10/7/2015 7:22 PM	Rate (0)
RetroK Bronze Member Joined: 5/1/2013 Last visit: 8/29/2024 Posts: 428 Rating: (4)	There is no cable connector another side. but I want to use this one. so,I have a connection to the TP cable.

Suggestion To thank Quote Answer

|

Share this page:

Share this page on...

Follow us on