Skip to Content

Register Login

Default Header

(header konnte nicht geladen werden)

Navigation

Problem establishing Connection with PLCSIM Advanced and downloading program.

Created by: ar102 at: 2/1/2019 4:09 PM (16 Replies)

Rating (1)

Thanks 5

Result pages:: |; 1 | 2; |

17 Entries

Entries per page: 10 | all

2/5/2019 8:55 PM	Rate (0)
ar102 Posts: 6 Rating: (0)	Firmware is V2.5 for the S71500 PLC I'm using. Kal.A What is the firmware configured for your device? You need V2.0 or higher? The error that concerns me and I've never seen before is the red diagnostic led in PLCSIM Advanced. Why is it on if the cpu was not connected.
ar102 Posts: 6 Rating: (0)
Suggestion To thank Quote Answer

2/5/2019 8:59 PM	Rate (0)
ar102 Posts: 6 Rating: (0)	I was finally able to successfully connect to the PLC and download. I believe the error LED was a result of a conflicting IP address with the one I was assigning to the PLC instance. There aren't any diagnostic messages in the program that tell you what the error LED is a result of so I can't be sure that this was the case. Kal.A I tried simulating your exact issue and couldn't do it. At the same time I'm confident you connection problem can be resolved by as assigning an IP as per screen shots in attached file. When you are finally able to connect I would be interested in knowing how you got the red diagnostic LED to light up in PLCSIM advanced, what kind of error do you have? I can get it to flash with the CPU sill in run mode (by adding diagnostic OBs) but I couldn't get it to flash in stop. Thanks
ar102 Posts: 6 Rating: (0)
Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users grrrrrroooo

4/27/2020 10:41 PM	Rate (0)
Pessoa Advanced Member Joined: 5/27/2014 Last visit: 10/14/2025 Posts: 2 Rating: (0)	Kal.A I tried simulating your exact issue and couldn't do it. At the same time I'm confident you connection problem can be resolved by as assigning an IP as per screen shots in attached file. When you are finally able to connect I would be interested in knowing how you got the red diagnostic LED to light up in PLCSIM advanced, what kind of error do you have? I can get it to flash with the CPU sill in run mode (by adding diagnostic OBs) but I couldn't get it to flash in stop. buy s Rockwell plc Thanks

Suggestion To thank Quote Answer

4/27/2020 10:43 PM	Rate (0)
Pessoa Advanced Member Joined: 5/27/2014 Last visit: 10/14/2025 Posts: 2 Rating: (0)	buy s Rockwell plc. work very well Thanks

Suggestion To thank Quote Answer

5/23/2022 4:31 PM	Rate (1)
YBS Regular Member Joined: 1/10/2018 Last visit: 4/2/2025 Posts: 5 Rating: (3)	I had this problem too. And i solved it by the next way: 1) In the TIA Portal in PLC properties against "Set IP adress in the project" I set "IP adress is set directly at the device"; 2) In the PLCSIM Advanced I set IP adress 192.168.1.* (like 192.168.1.20) against 192.168.0.*. Hope this will help you

Suggestion To thank Quote Answer
This contribution was helpful to 2 thankful Users yaneda AutoGen_3195502

11/11/2022 6:26 AM	Rate (0)
BINNGO Member Joined: 4/15/2021 Last visit: 9/25/2025 Posts: 1 Rating: (0)	You can access "Virtual simatic memory Card" then delete file in here

Suggestion To thank Quote Answer

5/31/2024 4:11 AM	Rate (0)
AutoGen_3195502 Posts: 1 Rating: (0)	Hello everyone, Thanks for the answer. Yes, indeed the solution was as you described, but unfortunately, I don't have enough time to investigate "why". Best regards, Adrian
AutoGen_3195502 Posts: 1 Rating: (0)
Suggestion To thank Quote Answer

|

Share this page:

Share this page on...

Follow us on