Skip to Content

Register Login

Default Header

(header konnte nicht geladen werden)

Navigation

Timers S5#

Created by: Paul_control at: 11/18/2005 11:21 PM (5 Replies)

Rating (2)

Thanks 1

6 Entries

11/18/2005 11:21 PM	Rate (0)
Paul_control Posts: 3 Rating: (0)	Hi, I have a simple question I guess. I just trying to insert a mark in the time pin in the timer block and I cant. Im using Step 7 and I need to put an adress from a Interfece in that space. What I need to do?, there is another kind of timer to acces that line?
Paul_control Posts: 3 Rating: (0)
Suggestion To thank Quote Answer

11/22/2005 11:27 AM	Rate (1)
Muthu Posts: 17 Rating: (2)	Hi, Insteed of using s5#.... u can use any word formats. That is, MW 122 DB11.DBW 10 I thing your doubt is clear.
Muthu Posts: 17 Rating: (2)
Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users Ayman Elotaify

7/22/2009 8:45 AM	Rate (0)
girja Posts: 2 Rating: (0)	Hi I have same dought,can we address timer value from Data Block or Memeory? How? I tried S5T#MW22 but its not taking. Any One Reply Thanks
girja Posts: 2 Rating: (0)
Suggestion To thank Quote Answer

7/22/2009 10:00 AM	Rate (0)
bigbang Experienced Member Joined: 9/16/2008 Last visit: 9/7/2025 Posts: 56 Rating: (0)	Hi giriraj, You can give MW11 but in time dont mention like S5T#MW11. Instead you can mention the MW11 directly. DB address also you can give. Only in the description of your varible you have to give the datatype as S5Time and in the timer you give DB xxx. DBW xxx. By default the DB it is taking 0 ms. You have to give what time you required. Regards

Suggestion To thank Quote Answer

7/22/2009 10:06 AM	Rate (0)
adilmahsan Posts: 71 Rating: (2)	s5time can be given in word format in this case, the lower 3 nibbles represent 3 bcd digits... the uppermost 2 bits are unused.. while bits 12 and 13 determine timer base... 00 implies 10 msec, 01 implies 100 msec, 10 imples 1 sec and 11 implies a base of 10 sec you can take time in integer, convert it into bcd, or it with w#16#2000 (for 1 sec time base) and then move it into the timer hope it helps if it doesn't, i can send you a program in which it has been done
adilmahsan Posts: 71 Rating: (2)
Suggestion To thank Quote Answer

7/22/2009 10:12 AM	Rate (1)
Jeebs Posts: 218 Rating: (28)	girja Hi I have same dought,can we address timer value from Data Block or Memeory? How? I tried S5T#MW22 but its not taking. Any One Reply Thanks Thats not going to work. First you have to understand the structure of the S5T# format. The S5T# data type is a word, thus made up out of 2 bytes, like: abbb (hex display of the word) a -> being the time resolution. 0 = 10ms 1 = 100ms 2 = 1s 3 = 10s b -> being the time in BCD, thus 0-999 Example: For 20s timer your MW22 should contain: 1200 as value Note: This is displayed in hex format, not integer. More info on this can be found in the help files. To make the timer use this time from data block or memory, you have to substitute S5T# for your MW22. So it's not S5T#MW22, but just MW22 Hope this helps.
Jeebs Posts: 218 Rating: (28)
Suggestion To thank Quote Answer

|

Share this page:

Share this page on...

Follow us on