Skip to Content

Register Login

Default Header

(header konnte nicht geladen werden)

Navigation

cursor keys do not work (LOGO TD)

Created by: Chekby at: 7/29/2011 4:18 PM (7 Replies)

Rating (0)

Thanks 0

8 Entries

7/29/2011 4:18 PM	Rate (0)
Chekby Posts: 2 Rating: (0)	Good morning gentlemen, I used the Soft Comfort apply once to program the cursor keys to control the current level of a device. However, the cursor keys did not work with LOGO TD. What can I do? Once you have the cursor keys to the equipment. Thank you for your attention.
Chekby Posts: 2 Rating: (0)
Suggestion To thank Quote Answer

7/29/2011 4:31 PM	Rate (0)
Wizard Diamond Member Joined: 4/24/2006 Last visit: 12/24/2025 Posts: 9097 Rating: (1202)	Dear Chekby, Have you seen this thread: /tf/WW/en/Posts/53920#top Best regards, Wizard

Suggestion To thank Quote Answer

7/29/2011 4:56 PM	Rate (0)
Chekby Posts: 2 Rating: (0)	Hello Wizard, I saw this topic and tried this, but it did not work. However, I have done wrong .. so here we go: I used the cursor key, setting the same as "Momentary pushbutton (make)", just do this or some additional configuration is required? I put the picture of my setup attached Attachment config_cursor_keys.jpg (740 Downloads)
Chekby Posts: 2 Rating: (0)
Suggestion To thank Quote Answer

7/29/2011 10:31 PM	Rate (0)
Toeternietoe Platinum Member Joined: 12/27/2006 Last visit: 11/17/2025 Posts: 1200 Rating: (116)	You have to press ESC & Cursor key at the same time. Setting of a momentary (pulsar) or kontakt (Interruptor) is only working in the simulation mode (LOGO!Soft)

Suggestion To thank Quote Answer

8/1/2011 11:42 AM	Rate (0)
Paulvdb Posts: 21 Rating: (2)	Have tried this too ... the cursor keys never work perfect (even with ESC key pressed at the same time) I tried this on a LOGO 5 and 6... none work good. My logo had to be operated in a factory by operators who don't have the time to "fiddle around" with buttons that don't work perfect. So I ended up adding "real" push buttons to my design... too bad ... I hope that Siemens does something about this in a next version...
Paulvdb Posts: 21 Rating: (2)
Suggestion To thank Quote Answer

8/1/2011 2:25 PM	Rate (0)
Toeternietoe Platinum Member Joined: 12/27/2006 Last visit: 11/17/2025 Posts: 1200 Rating: (116)	You can use the 4 F... keys on the TD. They dont need to use with the Esc key

Suggestion To thank Quote Answer

8/2/2011 7:50 AM	Rate (0)
Paulvdb Posts: 21 Rating: (2)	Never worked with the display unit, but I've been told that there the cursor keys DO work ...
Paulvdb Posts: 21 Rating: (2)
Suggestion To thank Quote Answer

12/10/2011 9:57 AM	Rate (0)
Oliver Gonzalez Posts: 27 Rating: (0)	Based on my experience, using the included cursor buttons as HMI (human machine interface = operator buttons) only leads to problems. Why? Because all the dirt gets inside the LOGO! through the buttons and then nothing works. It´s advisable to use good quality pushbuttons for operators, otherwise they will blame all your good work and your machine will be said to be a rubish only for the cost of a few buttons.
Oliver Gonzalez Posts: 27 Rating: (0)
Suggestion To thank Quote Answer

|

Share this page:

Share this page on...

Related topics by keywords:

Follow us on