Skip to Content

Register Login

Default Header

(header konnte nicht geladen werden)

Navigation

Project compatibility issue

Created by: Kyzen at: 5/16/2014 5:19 PM (7 Replies)

Rating (0)

Thanks 1

8 Entries

5/16/2014 5:19 PM	Rate (0)
Kyzen Posts: 5 Rating: (0)	Hey there, I am running into a situation where I cannot open a V12 project on a newly formatted machine with V12 on it. I get the error about installed software (see the first attached file), even though I have the software installed. Note: I recently re-formatted the PC to run on 64 bit OS I recently upgraded the project to V13, but am trying to open the pre-existing V12 left for now. Attachment error.jpg (226 Downloads)
Kyzen Posts: 5 Rating: (0)
Suggestion To thank Quote Answer

5/16/2014 5:20 PM	Rate (0)
Kyzen Posts: 5 Rating: (0)	Here is an image of my installed software screen : Attachment installed_software.jpg (217 Downloads)
Kyzen Posts: 5 Rating: (0)
Suggestion To thank Quote Answer

5/16/2014 5:22 PM	Rate (0)
S7 AUTOMAN Posts: 515 Rating: (56)	Kyzen Hey there, I am running into a situation where I cannot open a V12 project on a newly formatted machine with V12 on it. I get the error about installed software (see the first attached file), even though I have the software installed. Note: I recently re-formatted the PC to run on 64 bit OS I recently upgraded the project to V13, but am trying to open the pre-existing V12 left for now. hello, try and update it to SP1 and see
S7 AUTOMAN Posts: 515 Rating: (56)
Suggestion To thank Quote Answer

5/16/2014 5:25 PM	Rate (0)
Kyzen Posts: 5 Rating: (0)	detailed view of installed software Attachment detailed.jpg (177 Downloads)
Kyzen Posts: 5 Rating: (0)
Suggestion To thank Quote Answer

5/16/2014 5:26 PM	Rate (0)
S7 AUTOMAN Posts: 515 Rating: (56)	Service Pack 1 for SIMATIC WinCC V12 (TIA Portal) Service Pack 1 for SIMATIC STEP 7 V12 (TIA Portal) incl. PLCSIM Updates for STEP 7 V12 SP1 and WinCC V12 SP1
S7 AUTOMAN Posts: 515 Rating: (56)
Suggestion To thank Quote Answer

5/16/2014 5:28 PM	Rate (0)
Kyzen Posts: 5 Rating: (0)	I think you're right... silly mistake.
Kyzen Posts: 5 Rating: (0)
Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users S7 AUTOMAN

5/16/2014 5:48 PM	Rate (0)
Ayman Elotaify Diamond Member Joined: 5/28/2008 Last visit: 12/23/2025 Posts: 4522 Rating: (843)	Kyzen Hey there, I am running into a situation where I cannot open a V12 project on a newly formatted machine with V12 on it. I get the error about installed software (see the first attached file), even though I have the software installed. Note: I recently re-formatted the PC to run on 64 bit OS I recently upgraded the project to V13, but am trying to open the pre-existing V12 left for now. Hello, If you have project made with TIA Step 7 V13, you can not open with TIA Step7 V12. Hope this helps.
	Ayman Elotaify
Suggestion To thank Quote Answer

5/16/2014 6:00 PM	Rate (0)
Kyzen Posts: 5 Rating: (0)	I'm not opening the V13 in V12, i only posted that note to make sure that the previous V12 version I am working with didn't get effected by the upgrade/clone process. I am installing V12 SP1, I think that is my issue.
Kyzen Posts: 5 Rating: (0)
Suggestion To thank Quote Answer

|

Share this page:

Share this page on...

Follow us on