Skip to Content

Register Login

Default Header

(header konnte nicht geladen werden)

Navigation

History Data Block

Created by: 93Mustang at: 5/14/2008 9:51 PM (15 Replies)

Rating (0)

Thanks 0

Result pages:: |; 1 | 2; |

16 Entries

Entries per page: 10 | all

5/16/2008 2:51 PM	Rate (0)
Aret Posts: 2348 Rating: (265)	Your temp isjust pointer! But to make it you should apply following : pointer = bit_number + 8*byte_number. So pointer P#2.3 would look like DW#16#13. When you make L/T instruction you specify data type TDBD[#temp] would make transfer forDWORD,beginningataddress,specifiedin#temp. TDBB[#temp] would make transfer forBYTE ,beginningataddress,specifiedin#temp. Please mention #temp in both cases is the same. PS. Refer to Step7 help, chapters area-internal indirect addressing. After that area-crossing indirect addressing would be helpfull. And after these 2 you can read register addressing and ANY pointers. Guess then you would be pointer expert:^)
Aret Posts: 2348 Rating: (265)	Last edited by: Aret at: 5/16/2008 2:56 PM
Suggestion To thank Quote Answer

5/16/2008 8:12 PM	Rate (0)
Denilson Pegaia Diamond Member Joined: 9/23/2005 Last visit: 12/26/2025 Posts: 4434 Rating: (1487)	Hi, some time I have wrotte a FAQ with a solution for "stacks". It was approved but until now not published. I attached a prototipe. I hope that lose many and many different types of tasks whitout "stress" Attachment FAQ stacker div.zip (379 Downloads)
	Denilson Pegaia Siemens Industry Sector Technical Support
Suggestion To thank Quote Answer

5/18/2008 9:17 PM	Rate (0)
Zenta Silver Member Joined: 10/12/2006 Last visit: 12/4/2025 Posts: 206 Rating: (26)	93Mustang So when your doing T DBD [#temp] the value in #temp is a bit pointer even though in my DB the data type is Real ? Hi, yes the pointer is a bit pointer.... the data type is irrelevant.... if you use 1. L L#0 (or L L#767567) the data type is dint 2. L 0.3 (or L 2323.12323) the data type is real... 3. L MD10 (the MD10 is a rael the data type is real etc.....) so the data type depend the load command.... Best regards Zenta

Suggestion To thank Quote Answer

5/21/2008 2:05 PM	Rate (0)
93Mustang Posts: 65 Rating: (0)	After much trial and error this was my final solution to this problem!! Attachment history.jpg (344 Downloads)
93Mustang Posts: 65 Rating: (0)
Suggestion To thank Quote Answer

6/10/2008 3:21 AM	Rate (0)
93Mustang Posts: 65 Rating: (0)	I'm considering doing this in a different way without the need for indirect addressing or a counter. Is there an instruction that can shift double words in a datablock for up to 50 real data values. This way I could just keep shifting the data and copy the newest data to DB75.DBX0.0 every time I've experimented with SFC 20 but because the data areas overlap you have to use a dummy area first which wastes memory. Is there another way to do this ?
93Mustang Posts: 65 Rating: (0)
Suggestion To thank Quote Answer

6/10/2008 2:13 PM	Rate (0)
Aret Posts: 2348 Rating: (265)	1) There is no instruction to shift 2 doublewords 2) There is instruction to shift bytes in doubleword - CAD 3) Indirect addressing is exactly what you need in STL. In SCL it can be done using arrays.
Aret Posts: 2348 Rating: (265)
Suggestion To thank Quote Answer

|

Share this page:

Share this page on...

Follow us on