Skip to Content

Register Login

Default Header

(header konnte nicht geladen werden)

Navigation

Increment pointer

Created by: martan321123 at: 3/24/2019 5:47 PM (8 Replies)

Rating (1)

Thanks 0

9 Entries

3/24/2019 5:47 PM	Rate (0)
martan321123 Posts: 4 Rating: (0)	Hello guys, I have a problem with increment (shift) pointer. I need to move pointer about P#0.1. First value started on address Q1.0, next will be Q1.1 and so on. Thanks My code is A M 10.1 JC hop1 LAR1 P#0.0 hop1: A M 1.0 FP M 10.0 JCN end = Q [AR1,P#1.0] +AR1 P#0.1 // increment, but is not function, I do not know why S M 10.1 end: NOP 0
martan321123 Posts: 4 Rating: (0)	Last edited by: martan321123 at: 3/24/2019 5:50:47 PM Last edited by: martan321123 at: 3/24/2019 5:52:03 PM
Suggestion To thank Quote Answer

3/25/2019 8:25 AM	Rate (0)
jacek d Platinum Expert Joined: 9/23/2005 Last visit: 1/12/2026 Posts: 5154 Rating: (772)	Pretty normal, when code is not executed then it does nothing. You should think over how your loop should work. Especially the part in bold. martan321123 A M 10.1 JC hop1 LAR1 P#0.0 hop1: A M 1.0 FP M 10.0 JCN end = Q [AR1,P#1.0] +AR1 P#0.1 // increment, but is not function, I do not know why S M 10.1 end: NOP 0
	Regards, Jacek What is confusing you is the fact that you never see a number but always its digit representation. So you end up thinking that the number is the representation. - Andrej Bauer Any claims against me - based on whatever legal reason - resulting from the use of any code and/or ideas presented on this forum shall be excluded. #StayWithUkraine
Suggestion To thank Quote Answer

3/25/2019 9:05 AM	Rate (0)
martan321123 Posts: 4 Rating: (0)	Loop is OK.....I want If I click on the M1.0 the pointer in AR1 will be incremented. I tried this code and MW20 is incremented. I don´t see mistake in code, I am sorry A M 10.1 JC hop1 LAR1 P#0.0 T MD 50 hop1: A M 1.0 FP M 10.0 JCN end = Q [AR1,P#1.0] L MW 20 L 1 +I T MW 20 +AR1 P#0.1 // increment, but is not function, I do not know why S M 10.1 end: NOP 0
martan321123 Posts: 4 Rating: (0)
Suggestion To thank Quote Answer

3/25/2019 9:35 AM	Rate (0)
jacek d Platinum Expert Joined: 9/23/2005 Last visit: 1/12/2026 Posts: 5154 Rating: (772)	martan321123 A M 10.1 JC hop1 LAR1 P#0.0 T MD 50 hop1: A M 1.0 FP M 10.0 JCN end <-check (monitor) the contents of AR1 here = Q [AR1,P#1.0] L MW 20 L 1 +I T MW 20 +AR1 P#0.1 // increment, but is not function, I do not know why S M 10.1 <-and here end: NOP 0
	Regards, Jacek What is confusing you is the fact that you never see a number but always its digit representation. So you end up thinking that the number is the representation. - Andrej Bauer Any claims against me - based on whatever legal reason - resulting from the use of any code and/or ideas presented on this forum shall be excluded. #StayWithUkraine
Suggestion To thank Quote Answer

3/25/2019 10:20 AM	Rate (0)
martan321123 Posts: 4 Rating: (0)	I know, he is empty, so how is correct code for function?
martan321123 Posts: 4 Rating: (0)
Suggestion To thank Quote Answer

3/25/2019 12:02 PM	Rate (0)
jacek d Platinum Expert Joined: 9/23/2005 Last visit: 1/12/2026 Posts: 5154 Rating: (772)	What do you mean by "empty"?
	Regards, Jacek What is confusing you is the fact that you never see a number but always its digit representation. So you end up thinking that the number is the representation. - Andrej Bauer Any claims against me - based on whatever legal reason - resulting from the use of any code and/or ideas presented on this forum shall be excluded. #StayWithUkraine
Suggestion To thank Quote Answer

3/25/2019 1:05 PM	Rate (0)
martan321123 Posts: 4 Rating: (0)	the value is to same P#0.0, correct?
martan321123 Posts: 4 Rating: (0)
Suggestion To thank Quote Answer

3/25/2019 1:13 PM	Rate (1)
jacek d Platinum Expert Joined: 9/23/2005 Last visit: 1/12/2026 Posts: 5154 Rating: (772)	No, it is not good. To make the story short. Modify your code as below. And make sure MD50 is not used anywhere else. jacek d martan321123 A M 10.1 JC hop1 LAR1 P#0.0 TAR1 T MD 50 hop1: A M 1.0 FP M 10.0 JCN end L MD 50 LAR1 = Q [AR1,P#1.0] L MW 20 L 1 +I T MW 20 +AR1 P#0.1 // increment, but is not function, I do not know why TAR1 T MD 50 S M 10.1 end: NOP 0
	Regards, Jacek What is confusing you is the fact that you never see a number but always its digit representation. So you end up thinking that the number is the representation. - Andrej Bauer Any claims against me - based on whatever legal reason - resulting from the use of any code and/or ideas presented on this forum shall be excluded. #StayWithUkraine
Suggestion To thank Quote Answer

3/26/2019 8:50 AM	Rate (0)
mitti Posts: 1 Rating: (0)	thanks for your help, I thought than it is posiible to make it without merker. But I have to reset output for set current output A M 1.2 JC hop1 LAR1 P#0.0 TAR1 T MD 10 hop1: A M 255.5 //blinking merker byte FP M 1.1 JCN end L 0 T QB 0 L MD 10 LAR1 = Q [AR1,P#0.0] +AR1 P#0.1 TAR1 T MD 10 S M 1.2 end: NOP 0
mitti Posts: 1 Rating: (0)	Last edited by: mitti at: 3/26/2019 8:52:37 AM
Suggestion To thank Quote Answer

|

Share this page:

Share this page on...

Follow us on