Skip to Content

Register Login

Default Header

(header konnte nicht geladen werden)

Navigation

step 7 help

Created by: bandr at: 7/30/2020 11:39 AM (15 Replies)

Rating (0)

Thanks 0

Result pages:: |; 1 | 2; |

16 Entries

Entries per page: 10 | all

8/7/2020 7:04 AM	Rate (0)
fritz Diamond Expert Joined: 10/7/2005 Last visit: 1/11/2026 Posts: 3054 Rating: (1062)	Putting aside that you provided an online backup without symbol names or comments, FC100/NW 7 runs a loop that resets the following bits in DB8 every OB 1 cycle (at first glance anyhow, suggest you test and verify yourself, these do encompass your Flowmeter Set bits at least though): DBX46.0 DBX86.0 DBX126.0 . . DBX1406.0 DBX1446.0 DBX1486.0 FC8 and its calls to FC115 may add to this, but I haven't drilled deeper and the lack of comments don't help either. Attachment FC100 - cyclic DB8 bit reset.jpg (295 Downloads)
	Cheers fritz The advice and opinion given in this thread is that of the author and does not necessarily reflect the views of I S Systems Pty Limited. To find out how I S Systems can help you with your automation needs please visit www.issystems.com.au.
Suggestion To thank Quote Answer

8/11/2020 11:39 AM	Rate (0)
bandr Experienced Member Joined: 9/19/2014 Last visit: 3/20/2025 Posts: 71 Rating: (0)	Hallo all The video shows that the count resolution (DB8. DBX 366.0) disabled when the step is changed from 6 to 7, and the counter (DB8.DBD 374) stops counting cycles. This situation is simulated but I have the same problem with the hardware because of this there is an error in the count during operation. I somehow need to add a delay for DB8.DBX 366.0. P.S. NW 7 FC 100 is visible in the background, it does not work in this situation. https://youtu.be/W7FoJdcHgag
	Last edited by: budko at: 08/11/2020 11:41:05 Last edited by: budko at: 08/11/2020 11:59:18 Last edited by: Jen_Moderator at: 08/11/2020 12:42:28 Embedded video.
Suggestion To thank Quote Answer

8/11/2020 11:58 AM	Rate (0)
bandr Experienced Member Joined: 9/19/2014 Last visit: 3/20/2025 Posts: 71 Rating: (0)	this video can be seen nw 12 FC204. Network completly stops working after changing the step from 6 to 7. https://youtu.be/qCT3_rvzNiM
	Last edited by: budko at: 08/11/2020 12:06:11 Last edited by: budko at: 08/11/2020 12:17:44 Last edited by: Jen_Moderator at: 08/11/2020 12:43:09 Embedded video.
Suggestion To thank Quote Answer

8/13/2020 12:42 PM	Rate (0)
bandr Experienced Member Joined: 9/19/2014 Last visit: 3/20/2025 Posts: 71 Rating: (0)	Problem is solved.

Suggestion To thank Quote Answer

8/13/2020 1:24 PM	Rate (0)
ixo65 Grandmaster Joined: 12/18/2014 Last visit: 1/11/2026 Posts: 36434 Rating: (4547)	budko Problem is solved. And was is the solution?

Suggestion To thank Quote Answer

9/21/2020 5:52 PM	Rate (0)
bandr Experienced Member Joined: 9/19/2014 Last visit: 3/20/2025 Posts: 71 Rating: (0)	I copied the run counter and inserted it in the seventh step.

Suggestion To thank Quote Answer

|

Share this page:

Share this page on...

Follow us on