Skip to Content

Register Login

Default Header

(header konnte nicht geladen werden)

Navigation

cable PC/USB (6ED1057-1AA01-0BA0) "not found driver" Win7

Created by: MrBin at: 5/22/2014 11:00 AM (17 Replies)

Rating (0)

Thanks 1

18 Entries

Entries per page: 10 | all

5/22/2014 11:00 AM	Rate (0)
MrBin Posts: 90 Rating: (0)	I bought the cable PC/USB (6ED1057-1AA01-0BA0). when I plugged it into my laptop, I had a problem "not found driver". My laptop operate on Window 7 ultimate 32 bit. Please help me to handle this problem. Thanks everybody!
MrBin Posts: 90 Rating: (0)	Last edited by: GrasserF at: 5/22/2014 11:10 AM new subject after splitting from /tf/WW/en/Posts/106826#top
Suggestion To thank Quote Answer

5/22/2014 11:14 AM	Rate (0)
Marcjan Platinum Member Joined: 4/22/2010 Last visit: 3/31/2025 Posts: 5697 Rating: (716)	Hello, Please have a look here: Logo Demo software , upgrades/updates, drivers Normaly you get the question "instal USB driver during Logosoft instalation. If you ignore that, you have to instal the driver by yourself later. Regards, Marcjan
	Last edited by: Marcjan at: 5/22/2014 11:48 AM Problem solved? Please let us know! Please no technical questions by PM, use the forum sections for your questions.
Suggestion To thank Quote Answer

5/22/2014 1:33 PM	Rate (0)
Helmut_13 Posts: 2930 Rating: (432)	Hi, I assume you made some thiong wrong. Concerning the PI (Prodict Informtion sheet) here is the procees: 1. Plugh the cable into LOGO! 2. Install the driver 3. Connect the cable to your PC I hope you have the right LOGO! Soft Comfort Version supporting Win7 (LSC V7.1.51) So search in the forum about LOGO! USB. You should find instruction how to fix this. Hope this help.
Helmut_13 Posts: 2930 Rating: (432)
Suggestion To thank Quote Answer

5/25/2014 12:16 AM	Rate (0)
Juan.Mechatronic Posts: 98 Rating: (6)	Hi, which version of logosoft are you using? As the other experts said, may be the version or something you skip/did wrong, during the installation of LOGO Soft can be the problem Best regards
Juan.Mechatronic Posts: 98 Rating: (6)
Suggestion To thank Quote Answer

5/25/2014 9:31 AM
VVago Posts: 784 Rating: (53)	MrBin I bought the cable PC/USB (6ED1057-1AA01-0BA0). when I plugged it into my laptop, I had a problem "not found driver". My laptop operate on Window 7 ultimate 32 bit. Please help me to handle this problem. Thanks everybody! You should install cable driver software.
VVago Posts: 784 Rating: (53)
Suggestion Quote Answer

5/26/2014 6:56 AM	Rate (0)
MrBin Posts: 90 Rating: (0)	Thanks everybody! I fix that problem (I using the laptop operating on Window XP). But when I connect Laptop with Logo 230RC 6ED1052-1FB00-0BA5 via PC/USB cable, upload button (in Logo soft comfort V7 Software) is disable. Although Logo in stop mode. I want to upload program from Logo. I can't do that.
MrBin Posts: 90 Rating: (0)
Suggestion To thank Quote Answer

5/26/2014 7:18 AM	Rate (0)
Juan.Mechatronic Posts: 98 Rating: (6)	MrBin Thanks everybody! I fix that problem (I using the laptop operating on Window XP). But when I connect Laptop with Logo 230RC 6ED1052-1FB00-0BA5 via PC/USB cable, upload button (in Logo soft comfort V7 Software) is disable. Although Logo in stop mode. I want to upload program from Logo. I can't do that. Hey, But, can you download PC--> PLC? or is disable too? is it your software demo ? or have you tried reinstall? best regards
Juan.Mechatronic Posts: 98 Rating: (6)
Suggestion To thank Quote Answer

5/26/2014 8:08 AM	Rate (0)
Ste39 Platinum Member Joined: 1/21/2013 Last visit: 11/20/2024 Posts: 4620 Rating: (710)	Hello MrBin, You have installed a demo software provided by Marcjan? Marcjan wrote: RESTRICTION: You cannot transfer (download or upload) the circuit programs to/from a LOGO! via a programming cable. It is therefore also not possible to perform on-line monitoring or tests of a running program. These features are only possible with a full version of the software.
	Last edited by: Ste39 at: 5/26/2014 8:13 AM
Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users Marcjan

6/2/2014 3:43 PM	Rate (0)
MrBin Posts: 90 Rating: (0)	Hello! I installed a full version software. When I upload program from my logo, I get a notice shown in the attached picture. Although I have chosen the right interface. Attachment Pictures.zip (640 Downloads)
MrBin Posts: 90 Rating: (0)	Last edited by: MrBin at: 6/2/2014 3:59 PM
Suggestion To thank Quote Answer

6/2/2014 3:48 PM	Rate (0)
Ste39 Platinum Member Joined: 1/21/2013 Last visit: 11/20/2024 Posts: 4620 Rating: (710)	MrBin Hello! When I upload program from my logo, I get a notice shown in the attached picture. Hello Where is the attachment

Suggestion To thank Quote Answer

6/2/2014 4:04 PM	Rate (0)
MrBin Posts: 90 Rating: (0)	I'm sorry Ste39! I attached pictures.
MrBin Posts: 90 Rating: (0)
Suggestion To thank Quote Answer

6/2/2014 4:26 PM	Rate (0)
Ste39 Platinum Member Joined: 1/21/2013 Last visit: 11/20/2024 Posts: 4620 Rating: (710)	Sorry MrBin, I don't have my PC now, you can send via jpg?

Suggestion To thank Quote Answer

6/2/2014 6:31 PM	Rate (0)
Juan.Mechatronic Posts: 98 Rating: (6)	MrBin Hello! I installed a full version software. When I upload program from my logo, I get a notice shown in the attached picture. Although I have chosen the right interface. Have you select new interface? Did you change your COM? On windows you can see the COM on hardware manager Then select the same COM on LOGO soft Best regards
Juan.Mechatronic Posts: 98 Rating: (6)
Suggestion To thank Quote Answer

6/2/2014 7:09 PM	Rate (0)
desmul24 Posts: 378 Rating: (73)	MrBin Hello! I installed a full version software. When I upload program from my logo, I get a notice shown in the attached picture. Although I have chosen the right interface. Hello, It is difficult to tell from your picture, please attach the message on Info window (Tools>Info window (F4)). What is the version of your windows 7? 32bit or 64? Rgs,
desmul24 Posts: 378 Rating: (73)
Suggestion To thank Quote Answer

6/3/2014 4:53 AM	Rate (0)
MrBin Posts: 90 Rating: (0)	I use Window XP SP2, it's operating on virtual machine (VMWare Workstation software). Program in Logo is protected by password (I lost that password). All of these are reasons?
MrBin Posts: 90 Rating: (0)
Suggestion To thank Quote Answer

6/3/2014 6:33 AM	Rate (0)
Ste39 Platinum Member Joined: 1/21/2013 Last visit: 11/20/2024 Posts: 4620 Rating: (710)	Hello MrBin, Have you triedwith CTRL+H and select your right LOGO! ?

Suggestion To thank Quote Answer

6/3/2014 6:43 AM	Rate (0)
desmul24 Posts: 378 Rating: (73)	MrBin I use Window XP SP2, it's operating on virtual machine (VMWare Workstation software). Program in Logo is protected by password (I lost that password). All of these are reasons? Why you use vm? Why don't you install directly? This could be the problem.
desmul24 Posts: 378 Rating: (73)
Suggestion To thank Quote Answer

6/23/2014 12:34 PM	Rate (0)
Narrator1 Bronze Member Joined: 3/25/2013 Last visit: 4/7/2025 Posts: 176 Rating: (1)	New question split intoError when downloading program to newer LOGO!. With best regards, Narrator1

Suggestion To thank Quote Answer

|

Share this page:

Share this page on...

Related topics by keywords:

Follow us on