Skip to Content

SiePortal

The integrated platform for your product selection, buying and support workflow - bringing together Industry Mall and Online Support.

SiePortalDeutsch

Search

Home
Support Support
{{(apiData.Support | filter:{'rank':1}:true)[0].title}} Support
- Menu temporary not available
- Menu temporary not available
- Menue temporary not available
- {{item.title}}

Products & Services
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
Support Support
{{(apiData.Support | filter:{'rank':1}:true)[0].title}} Support
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
MySiePortal MySiePortal
{{(apiData.MySiePortal | filter:{'rank':1}:true)[0].title}} MySiePortal
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
Cart ({{apiData.CartCount}})

Navigation

G120p VFD Run do active

Created by: ControlsWizard at: 10/4/2017 6:57 AM (12 Replies)

Rating (0)

Thanks 1

Result pages:: |; 1 | 2; |

13 Entries

Entries per page: 10 | all

10/4/2017 6:57 AM	Rate (0)
ControlsWizard Posts: 27 Rating: (0)	Dear Experts, I have purchased one G120p Sinamics Drive ... i have enetered all the neccessary parameters in the drive and configured its DI DO AI AO....i didnt connected physical motor i just want to check my control wiring by using drive DI DO without motor connected.. as i am getting analogue reference as well as DI command for start which i configured ... but DO relay is not switching for run as i configured in the parameter... to generate DO run switch motor has to be connected or what it can be check without physical motor... Reply me asap Regards
ControlsWizard Posts: 27 Rating: (0)
Suggestion To thank Quote Answer

10/4/2017 7:19 AM	Rate (0)
Msorich Posts: 661 Rating: (40)	Which function performs youre DO?
Msorich Posts: 661 Rating: (40)
Suggestion To thank Quote Answer

10/4/2017 7:33 AM	Rate (0)
ControlsWizard Posts: 27 Rating: (0)	Msorich Which function performs youre DO? motor start configured DI0 .... ON AND OFF Motor run configured D01... Operation i am getting signal of 24VDC on DI0 But Drive Has to be Start .... and generate D01... its is not generating D01 there is not alarm present ....ready LED is glowing PS: i havent connected motor .... so is it required to connect Motor to generate D01?
ControlsWizard Posts: 27 Rating: (0)
Suggestion To thank Quote Answer

10/4/2017 7:43 AM	Rate (0)
Msorich Posts: 661 Rating: (40)	Look at input/outputs ---> Relay outputs. What's connected to youre Relay Output 0 and Relay Output 1???
Msorich Posts: 661 Rating: (40)	Last edited by: Msorich at: 10/4/2017 7:47:17 AM
Suggestion To thank Quote Answer

10/4/2017 7:54 AM	Rate (0)
ControlsWizard Posts: 27 Rating: (0)	Msorich Look at input/outputs ---> Relay outputs. What's connected to youre Relay Output 0 and Relay Output 1??? DO1 operations... DO2 Faults .. fault is ok ..... because when i am not getting any AI its generate fault due to wire breaj f3505 Regards
ControlsWizard Posts: 27 Rating: (0)
Suggestion To thank Quote Answer

10/4/2017 8:01 AM	Rate (0)
Msorich Posts: 661 Rating: (40)	ControlsWizard DO1 operations... DO2 Faults .. fault is ok ..... because when i am not getting any AI its generate fault due to wire breaj f3505 Regards no, no, no. tell me exactly what's connected to youre Output Relay 0 and 1. Look in Starter. As I wrote you above! See attachment! Attachment example.png (191 Downloads)
Msorich Posts: 661 Rating: (40)	Last edited by: Msorich at: 10/4/2017 8:10:39 AM
Suggestion To thank Quote Answer

10/4/2017 8:11 AM	Rate (0)
ControlsWizard Posts: 27 Rating: (0)	Msorich ControlsWizard DO1 operations... DO2 Faults .. fault is ok ..... because when i am not getting any AI its generate fault due to wire breaj f3505 Regards no, no, no. tell me exactly what's connected to youre Output Relay 0 and 1. Look in Starter. As I wrote you above! DO 0: r52.2 and with its Normally open contact connected to one relay run in a control circuit. DO 2: r52.3 and its Normally open contact connected to one trip relay in control circuit.
ControlsWizard Posts: 27 Rating: (0)
Suggestion To thank Quote Answer

10/4/2017 8:15 AM	Rate (0)
Msorich Posts: 661 Rating: (40)	52.3 -it's clear. There's no any faults there. 52.2 - Go online. Look in Diagnostics ---> Missing enables. What's there? It's clear r52.2 is active in case when IGBT module is enabled for operation. As there is not any load connected, any pulses are inhibited. Hope this helps! Msorich
Msorich Posts: 661 Rating: (40)	Last edited by: Msorich at: 10/4/2017 8:16:21 AM Last edited by: Msorich at: 10/4/2017 8:22:57 AM
Suggestion To thank Quote Answer

10/4/2017 8:22 AM	Rate (0)
ControlsWizard Posts: 27 Rating: (0)	Msorich 52.3 -it's clear. There's no any faults there. 52.2 - Go online. Look in Diagnostics ---> Missing enables. What's there? missing enables r46 0 off1 enable missing 30 speed controller inhibited
ControlsWizard Posts: 27 Rating: (0)
Suggestion To thank Quote Answer

10/4/2017 8:24 AM	Rate (0)
Msorich Posts: 661 Rating: (40)	It's clear r52.2 is active in case when IGBT module is enabled for operation. As there is not any load connected, any pulses are inhibited. Off1 -it's seriosly, if it's programmed, then you have to set "1" at this terminal. Speed controller is inhibited because it was not programmed. Usually the commissionin is being performed by Starter's Wizard. After that all enables become green. If wiring is OK. There shouldn't be any problem fo successful start. Hope this helps! Msorich
Msorich Posts: 661 Rating: (40)	Last edited by: Msorich at: 10/4/2017 8:27:32 AM Last edited by: Msorich at: 10/4/2017 8:27:51 AM Last edited by: Msorich at: 10/4/2017 8:28:23 AM Last edited by: Msorich at: 10/4/2017 8:34:18 AM
Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users ControlsWizard

|

Share this page:

Share this page on...

Related topics by keywords:

SINAMICS_G

Follow us on