SiePortal

The integrated platform for your product selection, buying and support workflow - bringing together Industry Mall and Online Support.

Products & Services
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
Support Support
{{(apiData.Support | filter:{'rank':1}:true)[0].title}} Support
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
MySiePortal MySiePortal
{{(apiData.MySiePortal | filter:{'rank':1}:true)[0].title}} MySiePortal
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
Cart ({{apiData.CartCount}})

Navigation

error F 7800, Sinamics V90 drive with S7-200 SMART CPU

5/24/2014 3:40 PM	Rate (0)
Damayanti Posts: 148 Rating: (3)	Dear Marcjan Sir, I am Using V90 drive with S7-200 SMART cpu . But initialiy , it communicated with V-assistant software. But now it shows error F 7800 It's meaning is not given in manual. But in V-assistant Help, it shows F 7800 means "No power unit present" I have done factory reset. Still it shows same fault. How to rectify. Please help. Drive is: 6SL3210-5FE10-4UA0 Motor is: 1FL6042-1AF61-0AA1 Warm regards, Damayanti
Damayanti Posts: 148 Rating: (3)	Last edited by: GrasserF at: 5/26/2014 10:20 AM new subject after splitting from /tf/WW/en/Posts/105826#top
Suggestion To thank Quote Answer

6/23/2014 8:00 AM	Rate (0)
Damayanti Posts: 148 Rating: (3)	is there any body, to help me? Damayanti
Damayanti Posts: 148 Rating: (3)
Suggestion To thank Quote Answer

5/6/2016 3:20 PM	Rate (0)
Arunkumar222 Posts: 17 Rating: (0)	HI, Im getting the same problem in V90 Error diplaying 7800 its not a common error, I guess so Please help me out..
Arunkumar222 Posts: 17 Rating: (0)
Suggestion To thank Quote Answer

5/6/2016 3:28 PM	Rate (0)
Arunkumar222 Posts: 17 Rating: (0)	Have you got any solution for this problem , please share it here. regards, M.Arun Kumar
Arunkumar222 Posts: 17 Rating: (0)
Suggestion To thank Quote Answer

5/7/2016 6:13 AM	Rate (0)
PISCEAN 2010 Diamond Member Joined: 4/23/2010 Last visit: 11/23/2024 Posts: 8092 Rating: (884)	F7800 significance is No power unit is present. i.e. either no parameters are stored in power units or power unit parameters cannot be read. Please check. If those are not readable then replace the power unit. HTH.

Suggestion To thank Quote Answer

6/25/2016 9:13 AM	Rate (0)
Esenbol Posts: 3 Rating: (0)	If a F7800 fault is display the inverter is damaged and must be replaced. What causes a F7800 and what is the remedy? Recommended avoidance measures that should be taken 1. Good EMC installation, the earthing must be connected as in the Operating Instructions. Customers should connect the grounding terminal to a good earth point. If the grounding the chip between control unit and the power board can be damage and the fault F7800 will occur. 2. PTO pins in terminal X8. The pins 15, 16, 40, 41, 42 and 43 is for the PTO function. The voltage of these pins is 5V differential signal. 1. These pins should not be connected together, even if the PTO function is not been used. If the standard Siemens cable is used you must insure that the terminals are not no external voltage source can come into contact with the conections 2. The PTO output is a 5V voltage differential output. The customer should correctly connect these pins and it is good practice to make sure the DC24V power supply to the PLC should have the same common terminal or damage will occur. 3. Any EMC disturbance through these pins may also damage the PTO chip. Shielded cable should be used.
Esenbol Posts: 3 Rating: (0)
Suggestion To thank Quote Answer

Share this page:

Share this page on...