Skip to Content

SiePortal

The integrated platform for your product selection, buying and support workflow - bringing together Industry Mall and Online Support.

SiePortalDeutsch

Search

Home
Support Support
{{(apiData.Support | filter:{'rank':1}:true)[0].title}} Support
- Menu temporary not available
- Menu temporary not available
- Menue temporary not available
- {{item.title}}

Products & Services
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
Support Support
{{(apiData.Support | filter:{'rank':1}:true)[0].title}} Support
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
MySiePortal MySiePortal
{{(apiData.MySiePortal | filter:{'rank':1}:true)[0].title}} MySiePortal
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
Cart ({{apiData.CartCount}})

Navigation

STEP 7 Basic v10.5 SP2 works in Windows 7 32bit Professional

Created by: christo at: 9/1/2010 3:28 PM (8 Replies)

Rating (1)

Thanks 2

9 Entries

9/1/2010 3:28 PM	Rate (1)
christo Experienced Member Joined: 12/15/2009 Last visit: 12/23/2025 Posts: 5 Rating: (1)	Tested software STEP 7 Basic v10.5 SP2 on Windows 7 32bit Professional. Install without any problems, only the unofficial message system. Running software without objections, to the proper operation of TIA Automation portal shut down all security systems and security on the network card.

Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users Denilson Pegaia

9/1/2010 5:29 PM	Rate (0)
Denilson Pegaia Diamond Expert Joined: 9/23/2005 Last visit: 12/24/2025 Posts: 4434 Rating: (1487)	thanks for your feed back Mr Szafrański I remember, however, that until a offitial release, there is no garanty to use the STEP 7 Basic on Windows 7.
	Denilson Pegaia Siemens Industry Sector Technical Support
Suggestion To thank Quote Answer

9/1/2010 8:07 PM	Rate (0)
0_Einstein Grandmaster-Expert Joined: 7/7/2010 Last visit: 12/23/2025 Posts: 16325 Rating: (2520)	I have windows 7 professional running TIA Portal (Basic 10.5 SP2) and WinCC Flexible. Running it inside a Virtual PC / XP Mode 32-bit session. That setup likes RAM, so the more you can give it, the better it will perform. Plus you get the low memory warnings less often
	science guy
Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users umencho

9/1/2010 8:29 PM	Rate (0)
umencho Grandmaster Joined: 3/21/2006 Last visit: 10/16/2025 Posts: 10239 Rating: (1183)	Pegaia ... I remember, however, that until a official release, there is no guaranty to use the STEP 7 Basic on Windows 7. Let's follow for the moment huggy_d1' way until spring of 2011. Best regards, Hristo Mihalev
	Last edited by: UMENCHO at: 9/1/2010 8:29 PM
Suggestion To thank Quote Answer

9/15/2010 2:44 PM	Rate (0)
christo Experienced Member Joined: 12/15/2009 Last visit: 12/23/2025 Posts: 5 Rating: (1)	For proper operation of Windows 7 32bit Professional, and the program STEP 7 Basic v10.5 SP2 requires a minimum of 2GB of RAM. For the smooth operation of the system and software STEP 7 Basic is good to have 4GB of RAM.

Suggestion To thank Quote Answer

4/5/2011 3:48 PM	Rate (0)
Andrew_Greece Posts: 6 Rating: (0)	Hallo I am Totaly NEW to this forum. My Greetings to all members. This is my first message and also my 2 cents regarding the TIA and WIN 7 OS. I have too manage to load the TIA PORTAL V10.5 to WIN7 PROFFESIONAL . I have managed also to make CONNECTION to PLC . I have managed to make a small LAD program and COMPILE IT - NO problem . However There is no way to DOWNLOAD program to PLC S7-1200 DC/DC/DC... I even put ip address manually and/or through PG/PC interface from control pane,... NO SUCCESS. Also I have tried from TIA PORTAL shortcut on desctop > Properties > Run as administrator > Run This program in Compatible MODE WINDOWS XP SP3... RESULTS always same... I HAVE CONNECTION but cannot DOWNLOAD or EVEN change MODE to S7-1200. Forgot to say that my S7-1200 runs a program previously loaded from a PC with OS WIN XP... The PLC runs BUT CANNOT STOP IT OR DOWNLOAD NEW PROGRAM from WIN 7 PROFESSIONAL. So my personal experience is that WIN7 run the TIA but cannot have connection...
Andrew_Greece Posts: 6 Rating: (0)
Suggestion To thank Quote Answer

4/5/2011 3:53 PM	Rate (0)
Andrew_Greece Posts: 6 Rating: (0)	My Second Post Also have tried to work the TIA with WIN7 PROFESSIONAL running XP MODE with 1.5GB RAM - Can alter the RAM and other parameters from SETTINGS. Also for some users I would suggest to Disable Integration features in order XPMODE leave them to proceed entering the environment... In other thread I will post my message for connection problems I am facing with TIA. Thanks
Andrew_Greece Posts: 6 Rating: (0)
Suggestion To thank Quote Answer

4/25/2011 3:49 PM	Rate (0)
Denilson Pegaia Diamond Expert Joined: 9/23/2005 Last visit: 12/24/2025 Posts: 4434 Rating: (1487)	Hi, there is now an offitial delivery release for TIA V11: Delivery release SIMATIC STEP 7 Professional V11 http://support.automation.siemens.com/BR/view/en/49639088 Delivery release SIMATIC WinCC V11 http://support.automation.siemens.com/BR/view/en/49740133 it is released to Windows 7
	Denilson Pegaia Siemens Industry Sector Technical Support
Suggestion To thank Quote Answer

4/26/2011 10:53 AM	Rate (0)
Andrew_Greece Posts: 6 Rating: (0)	Thank you for the information and interest... Great will wait then the releases and order ... The good think is that have upgrade to a 24' monitor and will have better visual for the STEP 7 now.
Andrew_Greece Posts: 6 Rating: (0)
Suggestion To thank Quote Answer

|

Share this page:

Share this page on...

Follow us on