Skip to Content

SiePortal

The integrated platform for your product selection, buying and support workflow - bringing together Industry Mall and Online Support.

SiePortalDeutsch

Search

Home
Support Support
{{(apiData.Support | filter:{'rank':1}:true)[0].title}} Support
- Menu temporary not available
- Menu temporary not available
- Menue temporary not available
- {{item.title}}

Products & Services
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
Support Support
{{(apiData.Support | filter:{'rank':1}:true)[0].title}} Support
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
MySiePortal MySiePortal
{{(apiData.MySiePortal | filter:{'rank':1}:true)[0].title}} MySiePortal
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
Cart ({{apiData.CartCount}})

Navigation

F60062, F60068 on Sinamics DCM

Created by: Omega at: 11/23/2011 10:34 PM (17 Replies)

Rating (0)

Thanks 0

Result pages:: |; 1 | 2; |

18 Entries

Entries per page: 10 | all

11/23/2011 10:34 PM	Rate (0)
Omega Posts: 13 Rating: (0)	marcoo hello, in a plant there is a Sinamics DCM and somethimes ONLY when I give the Start command bacame the Fault F60062 with r949---->2. Someone can Help me about this fault and, if it's a converter problem,what i can change? best regards Hello Folks, I´m with the same problem in several Sinamics DCM . I´m just power on the 24Vcc of electronic circuit, and the r50038(armature voltage actual value) = 1036.2 V !!!! (even with the 440Vac power off !!!! ) When I power on the 440 Vac of armature and field and sent the command of turn on, the drive goes to fault state = F60062 !!!! Other fault very common is F60068 ( Incorrect compensation values for power unit ). This two fault´s there´s something in common ??? Thanks.
Omega Posts: 13 Rating: (0)	Last edited by: O_Moderator at: 11/24/2011 10:31 AM new subject after splitting from /tf/WW/en/Posts/59205#top
Suggestion To thank Quote Answer

5/19/2012 5:54 AM	Rate (0)
Prasetio Posts: 4 Rating: (0)	Omega marcoo hello, in a plant there is a Sinamics DCM and somethimes ONLY when I give the Start command bacame the Fault F60062 with r949---->2. Someone can Help me about this fault and, if it's a converter problem,what i can change? best regards Hello Folks, I´m with the same problem in several Sinamics DCM . I´m just power on the 24Vcc of electronic circuit, and the r50038(armature voltage actual value) = 1036.2 V !!!! (even with the 440Vac power off !!!! ) When I power on the 440 Vac of armature and field and sent the command of turn on, the drive goes to fault state = F60062 !!!! Other fault very common is F60068 ( Incorrect compensation values for power unit ). This two fault´s there´s something in common ??? Thanks. Dear Colleagues, I have the same problem also.. i whole my experience: >30 Sinamics DCM not occured for F60068 but recently, 3 Sinamics DCM (6RA8085-6FV62...) occurs the Fault Before, Siemens replace the drive because of F60068 (1x = in armature sensing) Now the replacement shows F60068 (2x = in field sensing ) Does somebody could help me..
Prasetio Posts: 4 Rating: (0)
Suggestion To thank Quote Answer

9/22/2014 9:06 AM	Rate (0)
xemit Advanced Member Joined: 6/29/2009 Last visit: 12/12/2025 Posts: 4 Rating: (0)	What is really the issue of F60068. Where can we find the fix to this fault?

Suggestion To thank Quote Answer

9/22/2014 12:08 PM	Rate (0)
PISCEAN 2010 Posts: 8092 Rating: (884)	Please see the attached sheet. Attachment F60068.pdf (1694 Downloads)
PISCEAN 2010 Posts: 8092 Rating: (884)
Suggestion To thank Quote Answer

9/23/2014 2:47 AM	Rate (0)
xemit Advanced Member Joined: 6/29/2009 Last visit: 12/12/2025 Posts: 4 Rating: (0)	Thanks Piscean, Have already tried the remedy whihc is just "Power On/Off" before many times but nothing changes. Fault value is actually 15 "No compesnation values can be calculated'. Other drives does not behave the same although having similar application. Still confused. Cheers

Suggestion To thank Quote Answer

9/23/2014 8:14 AM	Rate (0)
PISCEAN 2010 Posts: 8092 Rating: (884)	Please check following points. Have you entered converter data, motor data correctly? Have you set P50076[0] & P50076[1] correctly? Have you saved the final data in ROM? HTH.
PISCEAN 2010 Posts: 8092 Rating: (884)
Suggestion To thank Quote Answer

9/29/2014 4:47 AM	Rate (0)
xemit Advanced Member Joined: 6/29/2009 Last visit: 12/12/2025 Posts: 4 Rating: (0)	Thanks again for the reply, Yes re-checked those parameters also a few times before,I'll check them again one more time. Other drives driving exactly the same load did not have the fault. At the moment the fault is disabled and the drive works perfectly. Cheers

Suggestion To thank Quote Answer

10/21/2014 11:28 AM	Rate (0)
Maciek W. Posts: 4 Rating: (0)	Hello, Which firmware version ? Try to downgrade firmware if you have the newest one. regards Maciek
Maciek W. Posts: 4 Rating: (0)
Suggestion To thank Quote Answer

1/15/2016 9:48 AM	Rate (0)
osman.92.35 Posts: 10 Rating: (0)	Hello, We have the same problem with sinamics dcm.(f60068-f60062).Firstly there was a problem with our compensation.Then we solve the problem.Does the problem depend on changing compensation values? If it depends on compensation , can I learn how to define the compensation values into the sinamics dcm? I am waiting for your help. Thanks.
osman.92.35 Posts: 10 Rating: (0)
Suggestion To thank Quote Answer

1/15/2016 11:45 AM	Rate (0)
PISCEAN 2010 Posts: 8092 Rating: (884)	Hello, Have you checked fault value at r0949? How much is it?
PISCEAN 2010 Posts: 8092 Rating: (884)
Suggestion To thank Quote Answer

|

Share this page:

Share this page on...

Related topics by keywords:

SINAMICS_DCM

Follow us on