Skip to Content

SiePortal

The integrated platform for your product selection, buying and support workflow - bringing together Industry Mall and Online Support.

SiePortalDeutsch

Search

Home
Support Support
{{(apiData.Support | filter:{'rank':1}:true)[0].title}} Support
- Menu temporary not available
- Menu temporary not available
- Menue temporary not available
- {{item.title}}

Products & Services
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
Support Support
{{(apiData.Support | filter:{'rank':1}:true)[0].title}} Support
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
MySiePortal MySiePortal
{{(apiData.MySiePortal | filter:{'rank':1}:true)[0].title}} MySiePortal
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
Cart ({{apiData.CartCount}})

Navigation

LOGO! 8 FS4 & S7-1200: Communication doesn't work.

Created by: Messian at: 7/19/2017 5:21 AM (13 Replies)

Rating (0)

Thanks 3

Result pages:: |; 1 | 2; |

14 Entries

Entries per page: 10 | all

7/19/2017 5:21 AM	Rate (0)
Messian Posts: 5 Rating: (0)	I have a LOGO 8! FS4 LOGO SOFT 8.1v y SIMATIC S7 1200 1214 AC / DC / RLY with firmware 4.2 TIA PORTAL 14V. I try to connect but nothing happens, S7 not receive anything . the communication doesn't work. ------------------------------------------------------------------------------------------ Split from LOGO! 8 FS4 & S7-1200 (FW4.1).
Messian Posts: 5 Rating: (0)	Last edited by: Jen_Moderator at: 7/19/2017 8:23:33 AM New subject after splitting
Suggestion To thank Quote Answer

7/19/2017 10:41 PM	Rate (0)
MicTsc Gold Member Joined: 11/16/2012 Last visit: 10/1/2024 Posts: 307 Rating: (52)	I think there is a general problem in communication between S7 1200 and LOGO! 8 FS04. But first of all, did you make sure that put/get is enabled in the S7 1200 config?

Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users abproj

7/21/2017 4:00 AM	Rate (0)
Messian Posts: 5 Rating: (0)	yes. Of course I put enable this option but nothing happens. I just send a pulse the logo8 fs4 to s7 1200 v4.2 and not received and sent anything, when I add a MOVE block output ENO is apparently disabled Attachment s7 0nline.JPG (754 Downloads)
Messian Posts: 5 Rating: (0)
Suggestion To thank Quote Answer

7/21/2017 4:08 AM	Rate (0)
Messian Posts: 5 Rating: (0)	El s7 1200 y el logotipo 8 están en la misma red. 192.168.0.1 con enrutador S7 1200 ac / dc / rly tia portal v14 firwmare 4.2 192.168.0.20 Logo 8 Fs4 logosoft 8.1 192.168.0.15 TSAP 20,00 TSAP 10,01 Attachment logo mapeo.JPG (729 Downloads)
Messian Posts: 5 Rating: (0)
Suggestion To thank Quote Answer

5/31/2018 2:00 PM	Rate (0)
VictoriaLorenzo Posts: 6 Rating: (1)	I just did the same exercise, and It doesn't work. Like you I have a LOGO FS4 and 1200 V4.1. Please, we need a solution!
VictoriaLorenzo Posts: 6 Rating: (1)
Suggestion To thank Quote Answer

6/4/2018 11:20 AM	Rate (0)
Jen_Moderator Diamond Member Joined: 6/19/2017 Last visit: 9/6/2024 Posts: 8175 Rating: (172)	New question published by frantam is split to a separate thread with the subject Data writting from S7-1200 to logo NOT work. Best regards Jen_Moderator

Suggestion To thank Quote Answer

6/18/2018 9:17 PM	Rate (0)
ixo65 Grandmaster-Expert Joined: 12/18/2014 Last visit: 11/12/2024 Posts: 34207 Rating: (4260)	VictoriaLorenzo I just did the same exercise, and It doesn't work. Like you I have a LOGO FS4 and 1200 V4.1. Please, we need a solution! Create the connection with the LOGO! as a client and the S7 as a server. In TIA: Make sure that in the "Special connection properties" the check mark "Active connection establishment" is removed. Make sure that in the device view, by the properties of the protection and security (connection mechanisms) the check mark is set for "permanent access for PUT/GET communication from remote partner". Attachment Screenshots.zip (619 Downloads)

Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users Noer396

6/19/2018 3:02 PM	Rate (0)
Jay. Posts: 1283 Rating: (105)	Same here. Even though I was able to communicate between logo and s7-1200 for one sensor with the help of IXO, I am still in doubt about the addressing concepts in PUT and Get and also in Logo and how they identify the address linking with network io. I am still testing many variables in that and couldn't find a fixed solution. Jay
Jay. Posts: 1283 Rating: (105)
Suggestion To thank Quote Answer

6/19/2018 3:12 PM	Rate (0)
ixo65 Grandmaster-Expert Joined: 12/18/2014 Last visit: 11/12/2024 Posts: 34207 Rating: (4260)	Jaya1189 Same here. Even though I was able to communicate between logo and s7-1200 for one sensor with the help of IXO, I am still in doubt about the addressing concepts in PUT and Get and also in Logo and how they identify the address linking with network io. I am still testing many variables in that and couldn't find a fixed solution. Jay No solution for you in PM of #dP? ixo65 Create the connection with the LOGO! as a client and the S7 as a server. In TIA: Make sure that in the "Special connection properties" the check mark "Active connection establishment" is removed. Make sure that in the device view, by the properties of the protection and security (connection mechanisms) the check mark is set for "permanent access for PUT/GET communication from remote partner". For me it works as stated in the above post by me. If you want, I will send you my test Project.
	Last edited by: ixo65 at: 6/19/2018 3:16:59 PM
Suggestion To thank Quote Answer

6/19/2018 3:44 PM	Rate (0)
Jay. Posts: 1283 Rating: (105)	ixo65 Jaya1189 Same here. Even though I was able to communicate between logo and s7-1200 for one sensor with the help of IXO, I am still in doubt about the addressing concepts in PUT and Get and also in Logo and how they identify the address linking with network io. I am still testing many variables in that and couldn't find a fixed solution. Jay No solution for you in PM of #dP? ixo65 Create the connection with the LOGO! as a client and the S7 as a server. In TIA: Make sure that in the "Special connection properties" the check mark "Active connection establishment" is removed. Make sure that in the device view, by the properties of the protection and security (connection mechanisms) the check mark is set for "permanent access for PUT/GET communication from remote partner". For me it works as stated in the above post by me. If you want, I will send you my test Project. His PM is just the basic settings to be made. Maybe I am not understanding the addressing part which makes my testing not work. Communication betwenb the plc is fine. Just the addressing in LOGO and S7 that's is where it's becoming more complicated for me Jay
Jay. Posts: 1283 Rating: (105)
Suggestion To thank Quote Answer

|

Share this page:

Share this page on...

Related topics by keywords:

Follow us on