Skip to Content

SiePortal

The integrated platform for your product selection, buying and support workflow - bringing together Industry Mall and Online Support.

SiePortalDeutsch

Search

Home
Support Support
{{(apiData.Support | filter:{'rank':1}:true)[0].title}} Support
- Menu temporary not available
- Menu temporary not available
- Menue temporary not available
- {{item.title}}

Products & Services
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
Support Support
{{(apiData.Support | filter:{'rank':1}:true)[0].title}} Support
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
MySiePortal MySiePortal
{{(apiData.MySiePortal | filter:{'rank':1}:true)[0].title}} MySiePortal
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
Cart ({{apiData.CartCount}})

Navigation

Sinamic S 120 Assume Control Priority at starter

Created by: arta_wahyu at: 11/27/2014 9:03 AM (9 Replies)

Rating (0)

Thanks 0

10 Entries

11/27/2014 9:03 AM	Rate (0)
arta_wahyu Posts: 30 Rating: (0)	Good afternoon I have problem when use assume control priority sinamic S 120 at starter to operate servo motor, when I set speed about 1000 rpm and I push ON the button at starter,the result " The Switch-on disable of the drive is active" and the drive can not ON after that I see the alarm, there is fault F07900.. and I check the remedy still not get solve of the problem.. maybe you have suggest for this problem for type single motor module 6SL3120-1TE21-8AA4 for type servo Motor 1FT6084-8AF7-4BA3-Z resolver 4 speed thank you Best Regards Arta W Attachment picture.jpg (376 Downloads)
arta_wahyu Posts: 30 Rating: (0)
Suggestion To thank Quote Answer

11/27/2014 9:10 AM	Rate (0)
ChristophD Grandmaster-Expert Joined: 5/12/2006 Last visit: 12/19/2025 Posts: 22816 Rating: (3073)	Hi, check the encoder Connection and encoder cables. The motor mlfb i can't configure in the catalog, the last 4 digits are right? regards Christoph

Suggestion To thank Quote Answer

11/27/2014 9:42 AM	Rate (0)
arta_wahyu Posts: 30 Rating: (0)	1FT6084-8AF71-4BA3-Z for order number motor, I have already check the connection for encoder resolvcer cable and there is no problem because the status LED for SMC 10 is green.. I try again to apply the remedy and I change the value p2177(0) from 0,02 to 65 s and than the drive can ON but result the setpoint speed not same with actual , I set 400 rpm but the actual is zero.. please give me advise thank you best regards Arta W Attachment assume control.jpg (298 Downloads)
arta_wahyu Posts: 30 Rating: (0)
Suggestion To thank Quote Answer

11/27/2014 9:49 AM	Rate (0)
ChristophD Grandmaster-Expert Joined: 5/12/2006 Last visit: 12/19/2025 Posts: 22816 Rating: (3073)	Hello, if actual is 0 then there is a problem between the Encoder an the SMC10 so that no postion values are send to SMC. Which Encoder Cable do you use? Regards Christoph

Suggestion To thank Quote Answer

11/27/2014 10:18 AM	Rate (0)
arta_wahyu Posts: 30 Rating: (0)	thank you for your respond for cable, I don't know the type but I can give you the picture of encoder cable the encoder cable use DB 9, so we must convert DB 9 to DB 25 because SMC 10 has DB 25 Connector, also you can see the LED status of SMC 10 is green.. Thank you best Regards Arta W Attachment connection cable.jpg (293 Downloads)
arta_wahyu Posts: 30 Rating: (0)
Suggestion To thank Quote Answer

11/27/2014 10:27 AM	Rate (0)
ChristophD Grandmaster-Expert Joined: 5/12/2006 Last visit: 12/19/2025 Posts: 22816 Rating: (3073)	Hi, wtf! this is a very bad solution for a encoder cabel, no shild ,nothing. PLease check that the relevant Pins from the motor encoder connected correct to the SMC. I don't know the pin Layout from the Adapter and don't know the pin Layout from the REFU CPU. Regards Christoph

Suggestion To thank Quote Answer

11/27/2014 10:35 AM	Rate (0)
arta_wahyu Posts: 30 Rating: (0)	Dear so what must I do to get best encoder cable? what type of cable we must use? also how about right wiring of encoder cable? Thank you Best Regards Arta W
arta_wahyu Posts: 30 Rating: (0)
Suggestion To thank Quote Answer

11/27/2014 10:39 AM	Rate (0)
arta_wahyu Posts: 30 Rating: (0)	maybe you can give me reference about the encoder cable wiring and type of encoder cable Thank you Best Regards Arta W
arta_wahyu Posts: 30 Rating: (0)
Suggestion To thank Quote Answer

11/27/2014 10:54 AM	Rate (0)
ChristophD Grandmaster-Expert Joined: 5/12/2006 Last visit: 12/19/2025 Posts: 22816 Rating: (3073)	Hello, for Resolver i use the Cable Type 6FX8002-2CF02 from siemens. regards Christoph

Suggestion To thank Quote Answer

11/28/2014 4:03 AM	Rate (0)
arta_wahyu Posts: 30 Rating: (0)	hello I will find and change it, if change with CAT 6 cable, still can? Thank you Best Regards Arta W
arta_wahyu Posts: 30 Rating: (0)
Suggestion To thank Quote Answer

|

Share this page:

Share this page on...

Related topics by keywords:

SINAMICS_S

Follow us on