SiePortal

The integrated platform for your product selection, buying and support workflow - bringing together Industry Mall and Online Support.

SiePortalDeutsch

Home
Support Support
{{(apiData.Support | filter:{'rank':1}:true)[0].title}} Support
- Menu temporary not available
- Menu temporary not available
- Menue temporary not available
- {{item.title}}

Products & Services
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
Support Support
{{(apiData.Support | filter:{'rank':1}:true)[0].title}} Support
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
MySiePortal MySiePortal
{{(apiData.MySiePortal | filter:{'rank':1}:true)[0].title}} MySiePortal
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
Cart ({{apiData.CartCount}})

Navigation

How to select encoder

Created by: PISCEAN 2010 at: 11/30/2010 7:58 AM (4 Replies)

Rating (0)

Thanks 0

5 Entries

11/30/2010 7:58 AM	Rate (0)
PISCEAN 2010 Diamond Expert Joined: 4/23/2010 Last visit: 11/23/2024 Posts: 8092 Rating: (883)	Hello Experts, We have to meet following application reuirement. Rotor shaft of weight 25 T is rotated at 1 RPM. Its angular rotary degree is to be measuered & displayed. Accuracy of rotary degree to measuered & displayed is 1 sec. e.g. if the rotor shaft is rotated & its actual angular position 10 degree 6 minute & 1 sec then it should be meaured & displayed as the exact value i.e. 10 degree 6 minute 1 sec. Also in case of power failuer this value should be memorised & after resuming power it must display the exact one. My question is can I select absolute encoder for this application & of how much PPR? Your hints/tips/comments in this regard are highly welcomed. Thanks & regards, DEEP.

Suggestion To thank Quote Answer

1/13/2011 6:14 AM	Rate (0)
Zahir Posts: 11 Rating: (0)	Hi, I have used 6FX2001-5xPXX SIMODRIVE Sensor before for a similar application, (determining wheel position/angle on pasenger bridge) with very good accuracy and very easy to use sensor. Further, the sensor has ProfiBus interface reducing cabling/interference issues. Check it out! Zahir
Zahir Posts: 11 Rating: (0)
Suggestion To thank Quote Answer

1/13/2011 9:44 AM	Rate (0)
PISCEAN 2010 Diamond Expert Joined: 4/23/2010 Last visit: 11/23/2024 Posts: 8092 Rating: (883)	Hi, Thanks for your reply. Which system this encoder is interfaced? In my case I need single axis DRO only. On that shaft slot machining operation is to be carried out. Shaft is indexed & locaked manually. DEEP.

Suggestion To thank Quote Answer

1/13/2011 2:09 PM

Rate (0)

Zahir

Posts: 11

Rating:

(0)

Deepstr2010:
Which system this encoder is interfaced? In my case I need single axis DRO only. On that shaft slot machining operation is to be carried out. Shaft is indexed & locaked manually.

The encorder is interfaced to s7 300 (315-2DP) through profibus.
I have attached the manual for your review.

Attachment

BHA.pdf (367 Downloads)

2/18/2015 3:48 PM	Rate (0)
Min_Moderator Platinum Member Joined: 9/3/2014 Last visit: 3/13/2019 Posts: 4760 Rating: (122)	New question published by husnindut is split to a separate thread with the subject How to set parameter with encoder in simoreg?. Best regards Min_Moderator

Suggestion To thank Quote Answer

Share this page:

Share this page on...

SiePortal

How to select encoder

Created by: PISCEAN 2010 at: 11/30/2010 7:58 AM (4 Replies)

Rating (0) Thanks 0

5 Entries

PISCEAN 2010

Zahir

PISCEAN 2010

Zahir

Attachment

Min_Moderator

5 Entries

Follow us on

Rating (0)

Thanks 0