SiePortal

The integrated platform for your product selection, buying and support workflow - bringing together Industry Mall and Online Support.

Products & Services
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
Support Support
{{(apiData.Support | filter:{'rank':1}:true)[0].title}} Support
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
MySiePortal MySiePortal
{{(apiData.MySiePortal | filter:{'rank':1}:true)[0].title}} MySiePortal
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
Cart ({{apiData.CartCount}})

Navigation

REPLACE of 6SN1145-1BA01-0BA0 E/R MODULE

3/19/2016 3:00 AM	Rate (0)
kawamoto Posts: 2 Rating: (0)	Hi, English is not good, but please forgive me. I use following SimoDrive 611. 6SN1145-1BA01-0BA0 E/R MODULE DIP-SW_ALL:OFF 6SN1123-1AA00-0CA0 LT MODULE 6SN1118-0AA11-0AA1 CONTROL CARD 6SN1114-0AA01-0AA0 PARAMETER BOARD DIP-SW_1 and 8 is ON 1FT5104-1AC71-1AB0 AC SERVO MOTOR The other day, 6SN1145-1BA01-0BA0 has failed. Since resolved After replacing the other machine of 6SN1145-1BA01-0BA0, was attached to buy a new 6SN1145-1BA01-0BA2. However, FAULT 7 occurs in that's 6SN1145-1BA01-0BA2 for a few hours. It does not occur that it is 6SN1145-1BA01-0BA0. It was solved by changing the PARAMETER BOARD,DIP-SW_1 only is ON,Kp is 4.0 to 0.5. If you want to replace with 6SN1145-1BA01-0BA2, do you need to change the parameters?
kawamoto Posts: 2 Rating: (0)
Suggestion To thank Quote Answer

3/19/2016 5:17 AM	Rate (0)
nulizhang Platinum Expert Joined: 10/17/2007 Last visit: 12/29/2025 Posts: 4566 Rating: (416)	NO, no need to change any thing, dip switch on the top of new power supply -0AA2, same as your old one.
	If you like my comments please use "Thank" bottom left or Rating Top right
Suggestion To thank Quote Answer

3/21/2016 3:14 AM	Rate (0)
kawamoto Posts: 2 Rating: (0)	Thank you. The function of DIP-SW S1.1 to S1.6 The same is the both 6SN1145-1BA01-0BA0 and 6SN1145-1BA01-0BA2 ？ Especially S1.6, ON：sinusoidal current operation OFF：squarewave current operation
kawamoto Posts: 2 Rating: (0)
Suggestion To thank Quote Answer

3/21/2016 4:43 AM	Rate (0)
nulizhang Platinum Expert Joined: 10/17/2007 Last visit: 12/29/2025 Posts: 4566 Rating: (416)	for your system --611A with 1FT5 motor, it is no use. if you want to check see attached picture--cut from Siemens manual PS: S2.1 =on it is only change motor rotary direction to CCW.--if you keep same set point polar fro 56/14. Attachment Infeed_S1_6.PNG (1080 Downloads)
	Last edited by: nulizhang at: 3/21/2016 4:55:44 AM add PS If you like my comments please use "Thank" bottom left or Rating Top right
Suggestion To thank Quote Answer

7/9/2021 1:36 PM	Rate (0)
gyactayo Posts: 2 Rating: (0)	Dear, need raplace 6SN1145-1BA01-0BA0 , WHAT WOULD BE THE APPROPRIATE? It could be him simodrive 6sn1145-1aa01-0aa1 thanks
gyactayo Posts: 2 Rating: (0)
Suggestion To thank Quote Answer

7/9/2021 2:04 PM	Rate (0)
PISCEAN 2010 Posts: 8092 Rating: (884)	gyactayo Dear, need raplace 6SN1145-1BA01-0BA0 , WHAT WOULD BE THE APPROPRIATE? It could be him simodrive 6sn1145-1aa01-0aa1 thanks 6SN1145-1AA01-0AA1 can not be replacement for 6SN1145-1BA01-0BA0. 6SN1145-1BA01-0BA0 - Regenrative Infeed 6SN1145-1AA01-0AA1 - Non regulated infeed
PISCEAN 2010 Posts: 8092 Rating: (884)
Suggestion To thank Quote Answer

Share this page:

Share this page on...