Skip to Content

Register Login

Industry Online Support

Technical Forum

Navigation

Backup CPU315-2DP

Created by: Sortym at: 4/6/2018 8:56 AM (15 Replies)

Rating (1)

Thanks 0

Result pages:: |; 1 | 2; |

16 Entries

Entries per page: 10 | all

4/6/2018 8:56 AM	Rate (0)
Sortym Member Joined: 4/19/2017 Last visit: 7/12/2018 Posts: 13 Rating: (0)	Good afternoon. I have an object with CPU315-2DP 6ES7315-2AH14-0AB0. When I try to make a "Upload station to PG", I get errors "Error in object info data" and then "Online CPU type 6ES7315-2AH14-0AB0 V3.3.10 unknown". I use Step 7 v.5.5 HF 5. In HARDWARE there are two CPUs with V.3.0 and V3.3. Please help.

Suggestion To thank Quote Answer

4/9/2018 8:49 AM	Rate (0)
Sortym Member Joined: 4/19/2017 Last visit: 7/12/2018 Posts: 13 Rating: (0)	Please help. I really need advice on the problem.
	Last edited by: Sortym at: 4/9/2018 8:49:36 AM
Suggestion To thank Quote Answer

4/9/2018 9:39 AM	Rate (0)
Duris_I Platinum Member Joined: 4/28/2015 Last visit: 2/27/2021 Posts: 7544 Rating: (606)	Hello, only idea, check if your real CPU type (also check firmware under front cover) is available on your HW library. If not, you need download update of HW.
	With kind regards... Duris_I
Suggestion To thank Quote Answer

4/9/2018 1:07 PM	Rate (0)
Sortym Member Joined: 4/19/2017 Last visit: 7/12/2018 Posts: 13 Rating: (0)	The HW library has V.3.0 and V3.3. The CPU itself is version 3.3.10. There is no nominal 3.3.10 in the library.

Suggestion To thank Quote Answer

4/9/2018 1:32 PM	Rate (0)
Duris_I Platinum Member Joined: 4/28/2015 Last visit: 2/27/2021 Posts: 7544 Rating: (606)	Hello, ok, via which interface you want make upload? Did you set correct settings on PG/PC interface? Do you see some your CPU via Accessible Nodes icon?
	With kind regards... Duris_I
Suggestion To thank Quote Answer

4/9/2018 1:45 PM	Rate (0)
mopS04 Platinum Expert Joined: 3/5/2014 Last visit: 2/26/2021 Posts: 4329 Rating: (824)	ha sortym, can you show us a screenshot of the behavior? FW-version 3.3.10 can not be projected. you can only project the first two numbers 3.3, the rest is just online and there´s no need and no possibility to project it. I recommend you to install the latest SP4 for Step7 5.5. You find it here: Trial-Download SIMATIC STEP 7 V5.5 SP4 also the latest HSP should be installed: STEP 7 V5.x Hardware Support Packages (HSPs - as at 03/2018) for installing hardware updates in the Hardware Configuration hope this helps, regards,
	There is no bad feedback! Please rate!
Suggestion To thank Quote Answer

4/9/2018 4:10 PM	Rate (0)
BeVee Gold Member Joined: 7/18/2011 Last visit: 1/25/2021 Posts: 518 Rating: (84)	Hi Sortym, Are you sure the PLC is programmed with Step 7 classic? Could it be that the program was downloaded to the PLC by TIA portal? Kind regards, BV

Suggestion To thank Quote Answer

4/10/2018 1:32 PM	Rate (0)
Sortym Member Joined: 4/19/2017 Last visit: 7/12/2018 Posts: 13 Rating: (0)	BeVee Hi Sortym, Are you sure the PLC is programmed with Step 7 classic? Could it be that the program was downloaded to the PLC by TIA portal? Kind regards, BV I do not know through which program the project was made. I need to make a backup copy of this CPU. Is there any point to try through TIA Portal?

Suggestion To thank Quote Answer

4/10/2018 1:46 PM	Rate (0)
Sortym Member Joined: 4/19/2017 Last visit: 7/12/2018 Posts: 13 Rating: (0)	mopS04 га сортим, можете ли вы показать нам скриншот поведения? FW-версия 3.3.10 нельзя проецировать. вы можете проецировать только первые два номера 3.3, остальное просто в сети, и нет необходимости и нет возможности проецировать его. Я рекомендую вам установить последний SP4 для Step7 5.5. Вы найдете его здесь: Trial-Download SIMATIC STEP 7 V5.5 SP4 также должен быть установлен последний HSP: Пакеты аппаратной поддержки STEP 7 V5.x (HSP - по состоянию на 03/2018) для установки обновлений оборудования в конфигурации оборудования надеюсь это поможет, С уважением, Attachment IMG_20180404_135752.jpg (22 Downloads)

Suggestion To thank Quote Answer

4/10/2018 1:49 PM	Rate (0)
Sortym Member Joined: 4/19/2017 Last visit: 7/12/2018 Posts: 13 Rating: (0)	Attachment IMG_20180404_135814.jpg (19 Downloads)

Suggestion To thank Quote Answer

|

Share this page:

Share this page on...

Follow us on