COM 143 for CP 143 TF

Hi Guys.

I make a trial between S5-135U CPU 928 with CP 143 card to communicate with S7-315 with CP 343-1.

Now I am stuck to go online with CP 143 using COM 143. Both Green and Red LEDs are Lit. It come out with error message "CP Interface not Ready". Either cable broken, CP is OFF, wrong path selected in path selection(this i dont understand) or wrong interface set in S5 KOMI.

The same AS511 cable i use to online to CPU 928 is working fine and CPU in RUN mode but program still empty.

Anybody have any ideas?

Thank you.

Hi azad_dsc

Can you provide full type number of CP card or post a picture of the CP card?

Which version of COM 143 are you using ?

Which cable are you using - type number?

You could try to switch the CP card to stop before you try to download.

Kind regards,
BV

azad_dsc

Hi Guys.

I make a trial between S5-135U CPU 928 with CP 143 card to communicate with S7-315 with CP 343-1.

Now I am stuck to go online with CP 143 using COM 143. Both Green and Red LEDs are Lit. It come out with error message "CP Interface not Ready". Either cable broken, CP is OFF, wrong path selected in path selection(this i dont understand) or wrong interface set in S5 KOMI.

The same AS511 cable i use to online to CPU 928 is working fine and CPU in RUN mode but program still empty.

Anybody have any ideas?

Thank you.

 Hello azad_dsc

I am assuming you have done already the following.

- Added communication blocks to the 928CPU (SYNCRON , SEND ALL , RECEIVE ALL ...) and properly configured / programmed them based on your SSNR number of the CP143 Card.

- Programmed the Eprom / RAM module of the CP Card with COM143 with the correct communication layer and parameters (mac adress of CP343-1 / TSAP's)

- depending on your CP143 Card you are using, the 135U Power supply has to be fitted with a 15V power module to supply power to the CP143 Card.

- ........ 

Reagrds / m.f.g

BeVee

Hi azad_dsc

Can you provide full type number of CP card or post a picture of the CP card?

Which version of COM 143 are you using ?

Which cable are you using - type number?

You could try to switch the CP card to stop before you try to download.

Kind regards,
BV

 Hi BeeVee,

CP 143 type nr - 6GK1143-0AB01.

COM 143 TF version 1.0.

S5 cable i dont have any part nr but have been use it for many years to online mostly with S5 CPU 115.

I have try to Stop the CP and get same result.

Attached is some pictures for S5 cable, software and error message.

legacy support

 Hello azad_dsc

I am assuming you have done already the following.

- Added communication blocks to the 928CPU (SYNCRON , SEND ALL , RECEIVE ALL ...) and properly configured / programmed them based on your SSNR number of the CP143 Card.

- Programmed the Eprom / RAM module of the CP Card with COM143 with the correct communication layer and parameters (mac adress of CP343-1 / TSAP's)

- depending on your CP143 Card you are using, the 135U Power supply has to be fitted with a 15V power module to supply power to the CP143 Card.

- ........ 

Reagrds / m.f.g

 Hi Legacy support,

- I have done the block in the 928 CPU following the document in FAQ 17661306.

- I dont have any Eprom/RAM on the CP so that i am trying to make setting online.

- my CP143 - 6GK1143-0AB01 and i read that this CP with 15V built in. I attach picture of PLC Rack with CPU and CP.

- but i notice one thing, i have a s5 cable bought from China and it have RX and TX LED. Once i connect to CPU, the RX LED is ON but when I connect to CP, no LED ON at all.

Thank you

Hi azad_dsc,

As far as i know, this type of CP card needs a RAM or EPROM module.
I know a CP 1430 can operate without a module, but i think for this type a module is mandatory.

Apart from that, you should check the DIP switch settings for the SSNR. This number is also needed as parameter for the synchron block, send all/receive all and individual job blocks.

I hope you connect your programming device to the upper 15p SUB-D connector

Kind regards,
BV