Skip to Content

Register Login

Industry Online Support

Technical Forum

Navigation

Communication between step7 5.4 plcsim and wincc 7.0

Created by: amandeep at: 11/17/2009 8:40 AM (19 Replies)

Rating (0)

Thanks 2

Result pages:: |; 1 | 2; |

20 Entries

Entries per page: 10 | all

5/22/2014 9:56 AM	Rate (0)
Ammy Platinum Member Joined: 4/19/2008 Last visit: 12/23/2019 Posts: 1522 Rating: (158)	M_syrian WINCC_v7 connect to PLCsim Dear Greeting i am already have project on HMI SIEMSN PC(wincc v7 ) AND 317F PLC is running i have tried to make simulation on my laptop for development but WINCC can’t see PLCSIM where is all the tag on wincc under TCP/IP there is any procedure for the setting for the laptop IP and network console and PLCSIM to make it works i was do that before but was long time can somebody help to exactly how to do with my kind regards Hello M_syrian, Are looking for this..... How can you link WinCC to S7 PLCSIM? this will help u to setup the WinCC with PLC Sim
	Last edited by: Ammy at: 5/22/2014 9:57 AM Ammy New for every one.............. “No duty is more urgent than that of returning thanks.” If Problem Solved......! I can't help you privately - please post in the Forums
Suggestion To thank Quote Answer

5/22/2014 10:23 AM	Rate (0)
M_syrian Regular Member Joined: 2/11/2011 Last visit: 12/26/2018 Posts: 9 Rating: (0)	thank you very much for your replay actuly wincc using TCP/IP and all tags setted there progect step7 F alsoe has the comunication throw TCP/IP in my laptob i try to put PC/PG intrface at PLCsim ISO but when it tray to download no comunication if also whant to set for profibus in wincc or MPI i should to move all the tags from TCP.IP driver to the MPI or PROFibus it will be also big job mybe i am not experiance at this but if you fine the problem or help i will be very thanks for you when i start wincc (using IE general and the name same of PC and same adrees of PC) how i can make comunication throw TCP/IP between PLCsim SIMATEC and wincc is it possiable my regards

Suggestion To thank Quote Answer

5/22/2014 10:52 AM	Rate (0)
Khaled_Ezzat Silver Member Joined: 9/7/2007 Last visit: 4/14/2019 Posts: 550 Rating: (61)	M_syrian thank you very much for your replay actuly wincc using TCP/IP and all tags setted there progect step7 F alsoe has the comunication throw TCP/IP in my laptob i try to put PC/PG intrface at PLCsim ISO but when it tray to download no comunication HiM_syrian In PC/PG interface just use PLCSim (TCP/IP) since all your tags has been installed in TCP/IP connection. Also, check the connection in PLCSim connection drop down window to be PLCSIM(TCP/IP) M_syrian when i start wincc (using IE general and the name same of PC and same adrees of PC) how i can make comunication throw TCP/IP between PLCsim SIMATEC and wincc is it possiable my regards Did you followAmmy sugestion belowand did not work well kindly. Ammy Hello M_syrian, Are looking for this..... How can you link WinCC to S7 PLCSIM? this will help u to setup the WinCC with PLC Sim Finaly, check all IP addresses for PLC and PC station, it must be the same network. Hope this helps, waiting for your reply.
	Best Regards
Suggestion To thank Quote Answer

5/22/2014 11:54 AM	Rate (0)
Ammy Platinum Member Joined: 4/19/2008 Last visit: 12/23/2019 Posts: 1522 Rating: (158)	M_syrian thank you very much for your replay actuly wincc using TCP/IP and all tags setted there progect step7 F alsoe has the comunication throw TCP/IP in my laptob i try to put PC/PG intrface at PLCsim ISO but when it tray to download no comunication if also whant to set for profibus in wincc or MPI i should to move all the tags from TCP.IP driver to the MPI or PROFibus it will be also big job mybe i am not experiance at this but if you fine the problem or help i will be very thanks for you when i start wincc (using IE general and the name same of PC and same adrees of PC) how i can make comunication throw TCP/IP between PLCsim SIMATEC and wincc is it possiable my regards Hello M_syrian, Let me Understand clearly, You have a system which is working with S7-300 F System with WinCC. & You want to checked the same Project thing on PLC Sim with WinCC on you Laptop ? if yes then Checked are able to download to PLC SIM ? then Checked the WinCC have you set the Above setting which I have post. waiting for your reply....
	Ammy New for every one.............. “No duty is more urgent than that of returning thanks.” If Problem Solved......! I can't help you privately - please post in the Forums
Suggestion To thank Quote Answer

5/22/2014 2:14 PM	Rate (0)
M_syrian Regular Member Joined: 2/11/2011 Last visit: 12/26/2018 Posts: 9 Rating: (0)	kindly you see the attchment of my project setting when i select ISO not possiable to dwonlaod and wincc no see the PLCsim your kind advice regards Attachment e.zip (155 Downloads)

Suggestion To thank Quote Answer

5/22/2014 2:48 PM	Rate (0)
Ammy Platinum Member Joined: 4/19/2008 Last visit: 12/23/2019 Posts: 1522 Rating: (158)	M_syrian kindly you see the attchment of my project setting when i select ISO not possiable to dwonlaod and wincc no see the PLCsim your kind advice regards Hello M_syrian, for ISO you have to set the MAC address in the PLC, What you have set in the WinCC Side TCP/IP System Parameter ? you have to Select the PLCSIM (TCP/IP). Let me know What you have set on your side
	Ammy New for every one.............. “No duty is more urgent than that of returning thanks.” If Problem Solved......! I can't help you privately - please post in the Forums
Suggestion To thank Quote Answer

5/22/2014 3:19 PM	Rate (0)
M_syrian Regular Member Joined: 2/11/2011 Last visit: 12/26/2018 Posts: 9 Rating: (0)	Greeting did you received my attachment e.zip 1-PLCsim set TCP /IP project possible to download everything is ok 2-winccv.7 tag assigned under TCP/IP and the wincc IE general has IP address same of my LAPTOB i have tried to give MAC address to IE but when i start Wincc run time started but no communication with PLC PLCsim have no MAC address in the settings * if choice the PC/PG interface ISO simatic can’t see the PLCsim regards

Suggestion To thank Quote Answer

5/22/2014 3:34 PM	Rate (0)
olloy Silver Member Joined: 8/27/2010 Last visit: 3/16/2016 Posts: 415 Rating: (35)	Hi! In WinCC explorer click on tag management, then simatic S7 protocol suite, then select a connection. There you can find a "unit" tab. Set device name to PLCSIM, press ok, and the restart wincc. Now you should be able to simulate tags from PLCSIM.

Suggestion To thank Quote Answer

5/22/2014 3:54 PM	Rate (0)
Ammy Platinum Member Joined: 4/19/2008 Last visit: 12/23/2019 Posts: 1522 Rating: (158)	M_syrian Greeting did you received my attachment e.zip 1-PLCsim set TCP /IP project possible to download everything is ok 2-winccv.7 tag assigned under TCP/IP and the wincc IE general has IP address same of my LAPTOB i have tried to give MAC address to IE but when i start Wincc run time started but no communication with PLC PLCsim have no MAC address in the settings * if choice the PC/PG interface ISO simatic can’t see the PLCsim regards Hello M_syrian, I have seen your Screen Shot, Have you checked What I have Mention in my above post Ammy What you have set in the WinCC Side TCP/IP System Parameter ? you have to Select the PLCSIM (TCP/IP). Let me know What you have set on your side M_syrian *i have tried to give MAC address to IE but when i start Wincc run time started but no communication with PLC From Where (Device) you have Given the MAC Address. You have to see on the CPU S7-300 & need to put in the Hardware Configuration.
	Ammy New for every one.............. “No duty is more urgent than that of returning thanks.” If Problem Solved......! I can't help you privately - please post in the Forums
Suggestion To thank Quote Answer

12/19/2016 11:53 AM	Rate (0)
Min_Moderator Platinum Member Joined: 9/3/2014 Last visit: 3/13/2019 Posts: 5119 Rating: (115)	New question published by Xurshid is split to a separate thread with the subject No connection between PLCSIM V5.4 and WinCC 7.0. Best regards Min_Moderator

Suggestion To thank Quote Answer

|

Share this page:

Share this page on...

Follow us on

Youtube