Skip to Content

Register Login

Industry Online Support

Technical Forum

Navigation

cu320 to 313c-2dp profibus commissioning

Created by: Ziemens at: 8/7/2009 8:10 AM (8 Replies)

Rating (0)

Thanks 0

9 Entries

8/7/2009 8:10 AM	Rate (0)
Ziemens Silver Member Joined: 3/2/2007 Last visit: 3/17/2021 Posts: 723 Rating: (5)	Hy, We have a cu320 that we want to connect to a cpu 313c-2dp through profibus network (with telegrams 390, 105, …). We are not able to display address parameter p0918 (with the BOP). How can we see and change it? What are the other parameters to be set in the cu320? Thank you · Control Unit CU320, profibus, 4 drive-cliq, 24 vdc 0.8 A, 8 di 8 dio, WxHxD 50x270x226 mm Siemens 6SL3040-0MA00-0AA1 · Cpu cpu 313c-2 dp, 32 kb ram, 24 vdc, 16 di/16 do Siemens 6ES7 313-6CF03-0AB0
	Last edited by: Ziemens at: 8/7/2009 8:12 AM Last edited by: Ziemens at: 8/7/2009 8:11 AM ... thank you ...
Suggestion To thank Quote Answer

8/7/2009 9:03 AM	Rate (0)
UMENCHO Diamond Member Joined: 3/21/2006 Last visit: 4/9/2021 Posts: 10220 Rating: (1162)	Hello, I suggest you to start with SINAMICS S120 Commissioning Manual Commissioning Regards, Hristo Mihalev

Suggestion To thank Quote Answer

8/7/2009 9:53 AM	Rate (0)
Ziemens Silver Member Joined: 3/2/2007 Last visit: 3/17/2021 Posts: 723 Rating: (5)	Thank you...
	... thank you ...
Suggestion To thank Quote Answer

8/7/2009 1:16 PM	Rate (0)
Ziemens Silver Member Joined: 3/2/2007 Last visit: 3/17/2021 Posts: 723 Rating: (5)	We are trying to change the active drive object on the BOP top left. It says in the “Commissioning Manual 07/2007”: – Press key "FN" and "Arrow up" -> the drive object number at the top left flashes – Select the required drive object using the arrow keys – Acknowledge using the "P" key But it is not working, nothing is flashing. Please advise what to do.Thanks
	... thank you ...
Suggestion To thank Quote Answer

8/9/2009 1:01 PM	Rate (0)
Bhaskaran Posts: 107 Rating: (12)	Ziemens We are trying to change the active drive object on the BOP top left. It says in the “Commissioning Manual 07/2007”: – Press key "FN" and "Arrow up" -> the drive object number at the top left flashes – Select the required drive object using the arrow keys – Acknowledge using the "P" key But it is not working, nothing is flashing. Please advise what to do.Thanks Hi ! Have you tried to keep both the keys pressed for a longer time.
Bhaskaran Posts: 107 Rating: (12)
Suggestion To thank Quote Answer

8/10/2009 7:50 AM	Rate (0)
Ziemens Silver Member Joined: 3/2/2007 Last visit: 3/17/2021 Posts: 723 Rating: (5)	Hy, the problem remained until we downloaded the program to the cu320. Only, then the parameter p918 was displayed! Strange thing! Thanks
	... thank you ...
Suggestion To thank Quote Answer

8/12/2009 8:19 PM	Rate (0)
JakitGT Posts: 31 Rating: (0)	Yes, in order for the BOP to change drive object numbers, the CU320 must first be "told" what drive objects exist. This can either be done via automatic configuration through the BOP (reads everything on Drive-Cliq), or by downloading a project via STARTER.
JakitGT Posts: 31 Rating: (0)
Suggestion To thank Quote Answer

8/13/2009 7:44 AM	Rate (0)
Ziemens Silver Member Joined: 3/2/2007 Last visit: 3/17/2021 Posts: 723 Rating: (5)	But if we want to set the profibus address of the cu320 via parameter p918, we cannot! We had to set the address with dip switches, then download the program, only after that p918 was visible to us… Are we missing something? Thanks
	... thank you ...
Suggestion To thank Quote Answer

8/13/2009 2:05 PM	Rate (0)
JakitGT Posts: 31 Rating: (0)	Ziemens, Sorry for the lack of understanding. In order to give the BOP "access" to p918, you must first set parameter p3 to 2 or higher (max of 4). This also assumes you have performed an Auto-configuration of the CU320. If the CU320 has not been commissioned (BOP shows "35" at startup), the p918 will not be accessible, and the profibus address will be based on the DIP switches. To perform Basic Configuration from factory default: (This does not set up non-DriveCliq motors, power units, profidrive telegrams.....etc. It merely reads the Drive Cliq Components and assigns drive object numbers) Set P009 to 1 Set P97 to 1 for servo (2 for vector) set P009 to 0 The CU will then take about 30 seconds to perform an autoconfiguration You can now set p0003 to 2 or higher, and p918 is accessible More info of P0003 per documentation: ------------------------------------------------------------------------------------------------- "p0003 BOP access level" Description: Sets the access level for reading and writing parameters using the Basic Operator Panel (BOP) and Advanced Operator Panel (AOP). Values: 0: User-defined 1: Standard 2: Extended 3: Expert 4: Service Note: Access level 0 (user-defined): Parameters from the user-defined list (p0013). Not used as of firmware version 2.6 (p0016). Access level 1 (standard): Parameters for the simplest operator control possibility (e.g. p1120 = ramp-function generator, ramp-up time). Access level 2 (extended): Parameters to operate the basic functions of the drive unit. Access level 3 (experts): Expert know-how is required for these parameters (e.g. BICO parameterization). Access level 4 (service): For these parameters, it is necessary that authorized service personnel enter the appropriate password (p3950).
JakitGT Posts: 31 Rating: (0)	Last edited by: JakitGT at: 8/13/2009 2:42 PM
Suggestion To thank Quote Answer

|

Share this page:

Share this page on...

Related topics by keywords:

Follow us on