Skip to Content

Register Login

Industry Online Support

Technical Forum

Navigation

download to OP77A

Created by: Ziemens at: 11/18/2015 2:22 PM (16 Replies)

Rating (0)

Thanks 4

Result pages:: |; 1 | 2; |

17 Entries

Entries per page: 10 | all

11/19/2015 1:03 PM	Rate (0)
Wizard Diamond Expert Joined: 4/24/2006 Last visit: 1/27/2021 Posts: 7907 Rating: (992)	Hello Ziemens, When you perform an OS update with the option "Reset to factory settings" (Only possible if you are using a PC/PPI multi master cable) you will have to boot the panel. After that the transfer will start automatically. Best regards, Wizard

Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users Ste39

11/19/2015 1:12 PM	Rate (0)
Ste39 Platinum Member Joined: 1/21/2013 Last visit: 1/27/2021 Posts: 4564 Rating: (692)	Ziemens which keys should we press to make the op77a switch to transfer mode? it is only displaying " ... contains free software ... " Hello, The problem is that !!! I don't know which buttons he pressed, because there are none available for the OP77 like on OP7 !!! For me you need a PPI Multimaster cable
	Last edited by: Ste39 at: 11/19/2015 1:12:33 PM Wizard faster :-)
Suggestion To thank Quote Answer

11/19/2015 1:24 PM	Rate (0)
Ziemens Silver Member Joined: 3/2/2007 Last visit: 12/21/2020 Posts: 716 Rating: (5)	will a usb to ppi cable work in this case? which transmission rate? and the dip switches on the op77a should be all off?
	... thank you ...
Suggestion To thank Quote Answer

11/19/2015 1:27 PM	Rate (0)
Wizard Diamond Expert Joined: 4/24/2006 Last visit: 1/27/2021 Posts: 7907 Rating: (992)	Hello, Yes, an USB PC/PPI multi master cable will work. Perhaps you can look at the following link: how can you transfer a WinCC flexible project serially to a panel? Best regards, Wizard

Suggestion To thank Quote Answer

11/19/2015 1:48 PM	Rate (0)
Ziemens Silver Member Joined: 3/2/2007 Last visit: 12/21/2020 Posts: 716 Rating: (5)	in Prosave i click the "Device status" button. but not connection is established between "ProSave" and the "operator panel". what can i do?
	... thank you ...
Suggestion To thank Quote Answer

11/19/2015 2:33 PM	Rate (0)
Ziemens Silver Member Joined: 3/2/2007 Last visit: 12/21/2020 Posts: 716 Rating: (5)	it works. i did exactly as described in the below link. switch off the power supply for the operator panel. use usb to ppi cable, all op77a dip switch off. open prosave, select op77a and communication type. goto os update, select image file, and click reset to factory settings. click os update. power up the op77a. ... [ Resetting the Operating System to the Factory Settings (Booting) ] https://support.industry.siemens.com/cs/document/19701610/how-do-you-do-an-%22operating-system-update%22-(os-update)-or-%22reset-to-factory-settings%22-on-operator-panels?dti=0&lc=en-US
	... thank you ...
Suggestion To thank Quote Answer
This contribution was helpful to 2 thankful Users Min_Moderator Ste39

5/22/2018 7:40 AM	Rate (0)
Jen_Moderator Moderator Joined: 6/19/2017 Last visit: 1/28/2021 Posts: 4427 Rating: (73)	New question published by Online Tech is split to a separate thread with the subject Want to copy the program to an op77a . Best regards Jen_Moderator

Suggestion To thank Quote Answer

|

Share this page:

Share this page on...

Follow us on