Skip to Content

Register Login

Industry Online Support

Technical Forum

Navigation

download to OP77A

Created by: Ziemens at: 11/18/2015 2:22 PM (16 Replies)

Rating (0)

Thanks 4

17 Entries

Entries per page: 10 | all

11/18/2015 2:22 PM	Rate (0)
Ziemens Silver Member Joined: 3/2/2007 Last visit: 12/21/2020 Posts: 716 Rating: (5)	we are trying to download a wincc flexible 2008 sp3 project to an hmi OP77A. but we cannot have a connection to the hmi. do we need an older version of wincc flexible? any possible workaround?
	... thank you ...
Suggestion To thank Quote Answer

11/18/2015 3:01 PM	Rate (0)
Ste39 Platinum Member Joined: 1/21/2013 Last visit: 2/20/2021 Posts: 4567 Rating: (692)	Ziemens we are trying to download a wincc flexible 2008 sp3 project to an hmi OP77A. but we cannot have a connection to the hmi. do we need an older version of wincc flexible? any possible workaround? Hello Ziemens, What cable you have for transfer project? Go to table 7.1.3 http://support.automation.siemens.com/WW/view/en/21084916 Projekttransfer_e_C1.pdf
	Last edited by: Ste39 at: 11/18/2015 3:24:26 PM Project transfer list
Suggestion To thank Quote Answer

11/18/2015 3:46 PM	Rate (0)
Ziemens Silver Member Joined: 3/2/2007 Last visit: 12/21/2020 Posts: 716 Rating: (5)	i am using usb to profibus adapter, baudrate 1.5 mbps.
	... thank you ...
Suggestion To thank Quote Answer

11/18/2015 3:55 PM	Rate (0)
Wizard Diamond Expert Joined: 4/24/2006 Last visit: 2/25/2021 Posts: 7939 Rating: (1003)	Hello Ziemens, Perhaps the following link might help: Which connector cables are available for connecting to SIMATIC Panels? how can you transfer a WinCC flexible project via MPI/PROFIBUS to a Windows-based panel? Best regards, Wizard

Suggestion To thank Quote Answer

11/18/2015 4:01 PM	Rate (0)
Ste39 Platinum Member Joined: 1/21/2013 Last visit: 2/20/2021 Posts: 4567 Rating: (692)	Ziemens i am using usb to profibus adapter, baudrate 1.5 mbps. hello Have you enabled the MPI/Profibus channel on the OP77A?

Suggestion To thank Quote Answer

11/19/2015 8:59 AM	Rate (0)
Ziemens Silver Member Joined: 3/2/2007 Last visit: 12/21/2020 Posts: 716 Rating: (5)	i did os update, it took two times to finish. but after it requested erase memory. then i could not transfer anymore. what are the default settings for download to OP77A? i am using a profibus cable.
	... thank you ...
Suggestion To thank Quote Answer

11/19/2015 9:02 AM	Rate (0)
Ziemens Silver Member Joined: 3/2/2007 Last visit: 12/21/2020 Posts: 716 Rating: (5)	it is only displaying "free software available..." !!!
	... thank you ...
Suggestion To thank Quote Answer

11/19/2015 9:12 AM	Rate (0)
Online Tech Platinum Member Joined: 3/28/2015 Last visit: 2/24/2021 Posts: 641 Rating: (191)	Hello, Perhaps the following topic might help: How do you do an "Operating system update" (OS update) or "Reset to factory settings" on operator panels?
	Eng.Mohamed Ibrahim Mobile & WhatsApp : +201122880543
Suggestion To thank Quote Answer

11/19/2015 9:26 AM	Rate (0)
Ste39 Platinum Member Joined: 1/21/2013 Last visit: 2/20/2021 Posts: 4567 Rating: (692)	Ziemens i did os update, it took two times to finish. but after it requested erase memory. then i could not transfer anymore. what are the default settings for download to OP77A? i am using a profibus cable. Hello Ziemens, Read carefully this thread: Op77 OS update failed - Industry Support Siemens
	Last edited by: Ste39 at: 11/19/2015 9:27:16 AM
Suggestion To thank Quote Answer

11/19/2015 12:50 PM	Rate (0)
Ziemens Silver Member Joined: 3/2/2007 Last visit: 12/21/2020 Posts: 716 Rating: (5)	which keys should we press to make the op77a switch to transfer mode? it is only displaying " ... contains free software ... "
	... thank you ...
Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users first mobile

11/19/2015 1:03 PM	Rate (0)
Wizard Diamond Expert Joined: 4/24/2006 Last visit: 2/25/2021 Posts: 7939 Rating: (1003)	Hello Ziemens, When you perform an OS update with the option "Reset to factory settings" (Only possible if you are using a PC/PPI multi master cable) you will have to boot the panel. After that the transfer will start automatically. Best regards, Wizard

Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users Ste39

11/19/2015 1:12 PM	Rate (0)
Ste39 Platinum Member Joined: 1/21/2013 Last visit: 2/20/2021 Posts: 4567 Rating: (692)	Ziemens which keys should we press to make the op77a switch to transfer mode? it is only displaying " ... contains free software ... " Hello, The problem is that !!! I don't know which buttons he pressed, because there are none available for the OP77 like on OP7 !!! For me you need a PPI Multimaster cable
	Last edited by: Ste39 at: 11/19/2015 1:12:33 PM Wizard faster :-)
Suggestion To thank Quote Answer

11/19/2015 1:24 PM	Rate (0)
Ziemens Silver Member Joined: 3/2/2007 Last visit: 12/21/2020 Posts: 716 Rating: (5)	will a usb to ppi cable work in this case? which transmission rate? and the dip switches on the op77a should be all off?
	... thank you ...
Suggestion To thank Quote Answer

11/19/2015 1:27 PM	Rate (0)
Wizard Diamond Expert Joined: 4/24/2006 Last visit: 2/25/2021 Posts: 7939 Rating: (1003)	Hello, Yes, an USB PC/PPI multi master cable will work. Perhaps you can look at the following link: how can you transfer a WinCC flexible project serially to a panel? Best regards, Wizard

Suggestion To thank Quote Answer

11/19/2015 1:48 PM	Rate (0)
Ziemens Silver Member Joined: 3/2/2007 Last visit: 12/21/2020 Posts: 716 Rating: (5)	in Prosave i click the "Device status" button. but not connection is established between "ProSave" and the "operator panel". what can i do?
	... thank you ...
Suggestion To thank Quote Answer

11/19/2015 2:33 PM	Rate (0)
Ziemens Silver Member Joined: 3/2/2007 Last visit: 12/21/2020 Posts: 716 Rating: (5)	it works. i did exactly as described in the below link. switch off the power supply for the operator panel. use usb to ppi cable, all op77a dip switch off. open prosave, select op77a and communication type. goto os update, select image file, and click reset to factory settings. click os update. power up the op77a. ... [ Resetting the Operating System to the Factory Settings (Booting) ] https://support.industry.siemens.com/cs/document/19701610/how-do-you-do-an-%22operating-system-update%22-(os-update)-or-%22reset-to-factory-settings%22-on-operator-panels?dti=0&lc=en-US
	... thank you ...
Suggestion To thank Quote Answer
This contribution was helpful to 2 thankful Users Min_Moderator Ste39

5/22/2018 7:40 AM	Rate (0)
Jen_Moderator Moderator Joined: 6/19/2017 Last visit: 2/25/2021 Posts: 4494 Rating: (75)	New question published by Online Tech is split to a separate thread with the subject Want to copy the program to an op77a . Best regards Jen_Moderator

Suggestion To thank Quote Answer

|

Share this page:

Share this page on...

Follow us on