Skip to Content

support.automation.siemens.com | Technical Forum | Saturday, December 14, 2019 6:50:52 AM

Drive Showing A083

Created by: Shivshanker at: 5/20/2012 10:22 AM (15 Replies)

Rating (0)

Thanks 1

Result pages:: |; 1 | 2; |

16 Entries

Entries per page: 10 | all

5/20/2012 10:22 AM	Rate (0)
Shivshanker Regular Member Joined: 3/30/2012 Last visit: 5/24/2019 Posts: 49 Rating: (1)	Hi I am Facing Problem with 6RA70 it continously showing Alarm A083 .I Changed the Cable Still Fault is not reseted.

Suggestion To thank Quote Answer

5/20/2012 10:39 AM	Rate (0)
PISCEAN 2010 Platinum Member Joined: 4/23/2010 Last visit: 12/14/2019 Posts: 5539 Rating: (414)	Hello, Drive is controlled by PLC or CNC? Is this a new machine under commissioning or old machine, running from long time? Have you checked the LED status on CBP2?

Suggestion To thank Quote Answer

5/20/2012 11:09 AM	Rate (0)
Shivshanker Regular Member Joined: 3/30/2012 Last visit: 5/24/2019 Posts: 49 Rating: (1)	Dear Sir Drive is PLC controlled.Machine is Running Since 1 year.LED Status Red &Yellow is Glowing and Green is not Glowing.

Suggestion To thank Quote Answer

5/20/2012 12:05 PM	Rate (0)
PISCEAN 2010 Platinum Member Joined: 4/23/2010 Last visit: 12/14/2019 Posts: 5539 Rating: (414)	Hello, Have you checked r650 bit 10 value?

Suggestion To thank Quote Answer

5/20/2012 1:01 PM	Rate (0)
Shivshanker Regular Member Joined: 3/30/2012 Last visit: 5/24/2019 Posts: 49 Rating: (1)	Dear Sir r650 bit 10 is high when There is no Alarm. At Time Of Alarm A083.we are not able see the status of this bit.

Suggestion To thank Quote Answer

5/20/2012 1:12 PM	Rate (0)
PISCEAN 2010 Platinum Member Joined: 4/23/2010 Last visit: 12/14/2019 Posts: 5539 Rating: (414)	Hello, Have you tried by changing cable along with terminal or you changed cable only by keeping terminals as it is? 1. Please check with PLC drive data block. 2. Please increase the time in U722 & check. (Telegram failuer time to process the data)
	Last edited by: PISCEAN 2010 at: 5/20/2012 1:23 PM
Suggestion To thank Quote Answer

5/20/2012 1:46 PM	Rate (0)
Shivshanker Regular Member Joined: 3/30/2012 Last visit: 5/24/2019 Posts: 49 Rating: (1)	Dear Sir We Changed The Cable with Terminals.We Can't see PLC programm and Drive Parameters as it is Locked By Some Other Person .

Suggestion To thank Quote Answer

5/20/2012 1:52 PM	Rate (0)
PISCEAN 2010 Platinum Member Joined: 4/23/2010 Last visit: 12/14/2019 Posts: 5539 Rating: (414)	shivsharma Dear Sir We Changed The Cable with Terminals.We Can't see PLC programm and Drive Parameters as it is Locked By Some Other Person . Please increase the value in U722 & check. If it doesn't help, then best way contact nearest Siemens office.

Suggestion To thank Quote Answer

5/20/2012 2:08 PM	Rate (0)
KSN Platinum Expert Joined: 8/25/2006 Last visit: 12/13/2019 Posts: 1940 Rating: (212)	Hello. Did you switch off and then switch on the drive after replacing cable? Try to remove and insert again CBP. Check connection of cable shielding.

Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users PISCEAN 2010

5/21/2012 7:51 AM	Rate (0)
Shivshanker Regular Member Joined: 3/30/2012 Last visit: 5/24/2019 Posts: 49 Rating: (1)	Dear Sir We Changed The CBP With New Card .Checked the screen ,replaced The Connectors.still Problem is as it is.

Suggestion To thank Quote Answer