Skip to Content

support.automation.siemens.com | Technical Forum | Saturday, December 14, 2019 4:32:43 PM

ET200S compact 16DI/16DO

Created by: Sanou at: 1/12/2018 1:42 PM (22 Replies)

Rating (3)

Thanks 2

Result pages:: |; 1 | 2 | 3; |

23 Entries

Entries per page: 10 | 20 | all

1/12/2018 1:42 PM	Rate (0)
Sanou Regular Member Joined: 7/27/2017 Last visit: 11/8/2018 Posts: 17 Rating: (0)	Hello everyone, I need help, I'm a beginner I have to configure the ET200 S compact 16DI/16DO. My CPU is 314C- 2 PN/DP. The problem is: LED SF red. LED BF flashing. Module configured but not available. Do you have any suggestion? Attachment 24251152_1632603243463805_1910695453_o.jpg (34 Downloads)

Suggestion To thank Quote Answer

1/12/2018 2:55 PM	Rate (1)
SCOTT123 Bronze Member Joined: 10/16/2007 Last visit: 10/10/2019 Posts: 396 Rating: (27)	Hello, check the Profibus-adress adjusted on the ET200S and also the wiring of the Profibus-plugs. Regards

Suggestion To thank Quote Answer

1/12/2018 3:59 PM	Rate (0)
Sanou Regular Member Joined: 7/27/2017 Last visit: 11/8/2018 Posts: 17 Rating: (0)	Hi, I have already checked it , and it is ok ! I have a question ; Should I define on HW config which terminal module TM I'm using ? Regards

Suggestion To thank Quote Answer

1/13/2018 8:54 PM	Rate (1)
Ste39 Platinum Member Joined: 1/21/2013 Last visit: 12/11/2019 Posts: 4369 Rating: (656)	Sanou Hi, I have already checked it , and it is ok ! I have a question ; Should I define on HW config which terminal module TM I'm using ? Regards Hello, Seems that you have only the CPU and this one slave, From CPU you have to go out with cable from A1-B1 and terminating resistor ON (on Profibus plug) On the ET200S you have to go in A1-B1 and terminating resistor ON (on Profibus plug) You did that?
	Last edited by: Ste39 at: 1/13/2018 9:03:21 PM
Suggestion To thank Quote Answer

1/17/2018 4:00 PM	Rate (0)
Sanou Regular Member Joined: 7/27/2017 Last visit: 11/8/2018 Posts: 17 Rating: (0)	Thank you for help. I did that, but I still have the error. Attachment 26857039_1681274458596683_28096824_n.jpg (21 Downloads)

Suggestion To thank Quote Answer

1/17/2018 10:06 PM	Rate (0)
Ste39 Platinum Member Joined: 1/21/2013 Last visit: 12/11/2019 Posts: 4369 Rating: (656)	Sanou Thank you for help. I did that, but I still have the error. Hello, still BF flashing?

Suggestion To thank Quote Answer

1/17/2018 10:09 PM	Rate (0)
Sanou Regular Member Joined: 7/27/2017 Last visit: 11/8/2018 Posts: 17 Rating: (0)	Yes It still flashing and on SF solid red

Suggestion To thank Quote Answer

1/17/2018 10:11 PM	Rate (0)
Ste39 Platinum Member Joined: 1/21/2013 Last visit: 12/11/2019 Posts: 4369 Rating: (656)	Sanou Yes It still flashing and on SF solid red Also on the ET200S BF flashing?

Suggestion To thank Quote Answer

1/17/2018 10:22 PM	Rate (0)
Sanou Regular Member Joined: 7/27/2017 Last visit: 11/8/2018 Posts: 17 Rating: (0)	The BF on ET 200S and the BF of CPU are flashing. It gives me on the diagnostic of slave : Error modul on slot 1 and No modul on slot 2 to 13

Suggestion To thank Quote Answer

1/17/2018 10:39 PM	Rate (0)
Ste39 Platinum Member Joined: 1/21/2013 Last visit: 12/11/2019 Posts: 4369 Rating: (656)	Sanou The BF on ET 200S and the BF of CPU are flashing. It gives me on the diagnostic of slave : Error modul on slot 1 and No modul on slot 2 to 13 Hello, 4 stupids questions: have you downloaded the Hardware configuration right? Are you sure that you have set the correct address? (post to us a photo of the dip switch address) cable, ground, terminating resistor are ok? the power on the ET200S is properly connected?
	Last edited by: Ste39 at: 1/17/2018 10:41:43 PM Last edited by: Ste39 at: 1/17/2018 11:20:05 PM
Suggestion To thank Quote Answer