Skip to Content

Register Login

Industry Online Support

Technical Forum

Navigation

How to set analog output in tiaportal S7-1200?

Created by: missosss123 at: 4/12/2018 10:43 AM (7 Replies)

Rating (0)

Thanks 2

8 Entries

4/12/2018 10:43 AM	Rate (0)
missosss123 Regular Member Joined: 3/26/2018 Last visit: 2/25/2021 Posts: 5 Rating: (0)	hi i like to ask how to set analog output in tiaportal S7-1200 ? KIRAN_DABHI THANKS FOR POST. THIS CALCULATION IS BASED ON RESOLUTION. ------------------------------------------------------------------------------------------ Split from Integer input range of analog module.
	Last edited by: Jen_Moderator at: 4/12/2018 2:14:39 PM New subject after splitting
Suggestion To thank Quote Answer

4/12/2018 12:51 PM	Rate (0)
mopS04 Platinum Expert Joined: 3/5/2014 Last visit: 4/20/2021 Posts: 4395 Rating: (843)	missosss123 hi i like to ask how to set analog output in tiaportal S7-1200 ? hi, which analog output? which address? analog outputs can´t be set. you are writing values to the adress of it and analog outputs giving out the range that is projected in the module-configuration dependent of the value you are writing to its address. hope thie helps, regards,
	Last edited by: mopS04 at: 4/12/2018 12:52:14 PM There is no bad feedback! Please rate!
Suggestion To thank Quote Answer

4/12/2018 2:32 PM	Rate (0)
Towome Platinum Expert Joined: 7/9/2015 Last visit: 4/19/2021 Posts: 2684 Rating: (346)	Hi, I don´t really know what you want to know - a guess is, that you have problems with standardize and destandadize? Please let me know if I am wrong or right. How do you standardize and destandardize analog values with STEP 7 (TIA Portal)? Regards, Towome
	If my post was useful, please rate me - thank you!
Suggestion To thank Quote Answer

4/12/2018 8:32 PM	Rate (0)
#dP Posts: 2826 Rating: (606)	Hello. missosss123 hi i like to ask how to set analog output in tiaportal S7-1200 ? KIRAN_DABHI THANKS FOR POST. THIS CALCULATION IS BASED ON RESOLUTION. ------------------------------------------------------------------------------------------ Split from Integer input range of analog module. Perhaps start with the video clip attached to this message. Regards. Attachment 2018-04-12_18-21-42.gif (1105 Downloads)
#dP Posts: 2826 Rating: (606)
Suggestion To thank Quote Answer

4/28/2018 2:30 PM	Rate (0)
missosss123 Regular Member Joined: 3/26/2018 Last visit: 2/25/2021 Posts: 5 Rating: (0)	Towome Hi, I don´t really know what you want to know - a guess is, that you have problems with standardize and destandadize? Please let me know if I am wrong or right. How do you standardize and destandardize analog values with STEP 7 (TIA Portal)? Regards, Towome Hi. We added new modules and forgot to upload HW. My fault
	Last edited by: missosss123 at: 4/28/2018 2:46:43 PM
Suggestion To thank Quote Answer

4/28/2018 2:38 PM	Rate (0)
missosss123 Regular Member Joined: 3/26/2018 Last visit: 2/25/2021 Posts: 5 Rating: (0)	HI. after first adding the module to HW. then it looks at which output has the same address. then the card or the card flashes or lights up green. and the tree according to the instructions in the reference. but in abbreviation input normalize then scale and output opposite the first scale then normalize. Input https://www.youtube.com/watch?v=YfYjn3cSOqA&t=456s Output https://www.youtube.com/watch?v=3GPMFrSe8ps&t=471s

Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users JGDS

4/30/2018 8:45 PM	Rate (0)
0_Einstein Diamond Expert Joined: 7/7/2010 Last visit: 4/20/2021 Posts: 10481 Rating: (1733)	Since the scale block requires a normalized input ranged from 0.0 to 1.0, you must have the norm_x block in front of the scale_x block if you want success. Is that what you are asking? missosss123 HI. after first adding the module to HW. then it looks at which output has the same address. then the card or the card flashes or lights up green. and the tree according to the instructions in the reference. but in abbreviation input normalize then scale and output opposite the first scale then normalize. Input https://www.youtube.com/watch?v=YfYjn3cSOqA&t=456s Output https://www.youtube.com/watch?v=3GPMFrSe8ps&t=471s
	science guy
Suggestion To thank Quote Answer

5/13/2018 6:02 PM	Rate (0)
missosss123 Regular Member Joined: 3/26/2018 Last visit: 2/25/2021 Posts: 5 Rating: (0)	huggy_d1 Since the scale block requires a normalized input ranged from 0.0 to 1.0, you must have the norm_x block in front of the scale_x block if you want success. Is that what you are asking? missosss123 HI. after first adding the module to HW. then it looks at which output has the same address. then the card or the card flashes or lights up green. and the tree according to the instructions in the reference. but in abbreviation input normalize then scale and output opposite the first scale then normalize. Input https://www.youtube.com/watch?v=YfYjn3cSOqA&t=456s Output https://www.youtube.com/watch?v=3GPMFrSe8ps&t=471sN Nope. I am stupid becouse we adding new external module and i do not dawnload HW to PLC.

Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users 0_Einstein

|

Share this page:

Share this page on...

Follow us on