11/24/2015 9:35 AM | |
Joined: 12/18/2014 Last visit: 4/25/2024 Posts: 32887 Rating: (4066) |
You can use the logo 6ED1052-1MD00-0BA8 with 12VDC or 24VDC. But not mixed.
For first steps: https://sitrain.automation.siemens.com/sitrain/open_wbt/logo/index.html The Manual you can download here: https://support.industry.siemens.com/cs/document/100761780/logo!?dti=0&lc=en-WW |
11/24/2015 10:53 AM | |
Joined: 1/21/2013 Last visit: 3/19/2024 Posts: 4618 Rating: (705) |
Hello, Why you cannot an upgrade of sofware to V8? LOGO! Demo software , upgrades/updates, drivers - SiemensUSB-PPI cable for LOGO! ? perhaps for S7 200 |
11/24/2015 11:08 AM | |
Posts: 16 Rating: (0) |
so i return the usb-ppi cable to the seller, clear na ? |
11/24/2015 11:20 AM | |
Joined: 12/18/2014 Last visit: 4/25/2024 Posts: 32887 Rating: (4066) |
|
Last edited by: ixo65 at: 11/24/2015 11:21:19 AM |
|
11/24/2015 3:17 PM | |
Joined: 1/21/2013 Last visit: 3/19/2024 Posts: 4618 Rating: (705) |
Hello, I think this is your LOGO! (look the code) and download the datasheet and have a look under "Relay outputs" --> Switching capacity of contacts: 6ED10521MD000BA8 - Industry Mall - Siemens |
Last edited by: Ste39 at: 11/24/2015 3:17:43 PM |
|
This contribution was helpful to1 thankful Users |
11/24/2015 3:23 PM | |
Joined: 1/21/2013 Last visit: 3/19/2024 Posts: 4618 Rating: (705) |
Hello, Please have a look some example: LOGO! Application Examples - PLCs - Siemens |
11/24/2015 5:40 PM | |
Joined: 3/28/2015 Last visit: 4/19/2024 Posts: 721 Rating: (213) |
Hello, Perhaps the following topic might help: |
Eng.Mohamed Ibrahim |
|
11/24/2015 6:03 PM | |
Posts: 16 Rating: (0) |
pls tell me how to fetch the program Ladder/fbd in logo by logosoft back |
11/24/2015 6:51 PM | |
Posts: 16 Rating: (0) |
Hi i want to know how to open a uploaded program in plc module by logosoft |
11/24/2015 6:57 PM | |
Joined: 12/18/2014 Last visit: 4/25/2024 Posts: 32887 Rating: (4066) |
Look at attachment.
AttachmentTest.wmv (280 Downloads) |
11/25/2015 8:39 PM | |
Posts: 16 Rating: (0) |
pls reply |
11/26/2015 8:50 AM | |
Joined: 1/21/2013 Last visit: 3/19/2024 Posts: 4618 Rating: (705) |
Hello, you can insert a fuse below 1A, then you can put one of 800mA as the series 477 of the catalog below for example: 5x20mm Fuses - Littelfuse |
11/27/2015 9:45 AM | |
Posts: 16 Rating: (0) |
No no i just want to clear myself should i use the 250 V 750mA fuse i have written before with my 12 V 1A DC adaptor |
11/27/2015 6:00 PM | |
Posts: 16 Rating: (0) |
hi while reading the manual of logo 8 suggested by ixo65 [https://support.industry.siemens.com/cs/document/100761780/logo!?dti=0&lc=en-WW pg-49 ] pls see the attached image ------- i have marked the points below with the same number encircled red, 1. i found i have to connect "Ground" near the RJ45 ethernet port, now my confusion is that I am using a DC power supply with only two pins + and - so should i connect this "Ground" to the - (negative) wire of my supply, clearly i mean that i short this "Ground" and "M' of the logo 8 ------- is it OK 2. the second confusion is that I could not find the current limit of inputs of logo whether i connect fuse (750mA,250 V or what value) to each input I1, I2 ... I8 that i use along with on main supply L+ 3. should i use a fuse for o/p relay contacts for their protection thanks, pls reply soon |
11/28/2015 5:13 PM | |
Posts: 16 Rating: (0) |
pls reply, pls pls |
12/2/2015 6:26 AM | |
Posts: 16 Rating: (0) |
Pls anybody reply the circuit i made is ok and safe or not? pls reply so that i can give a safe 1st start with my logo 8 thanks |
8/29/2017 8:38 AM | |
Joined: 8/21/2014 Last visit: 4/25/2024 Posts: 952 Rating: (13) |
New question published by Casiba is split to a separate thread with the subject Logo 8 Getting started. Best regards |
My Forum is the place to personalize your profile, |
|
Follow us on