Navigation

NCK adress change in CCU2 by HT6

Created by: Gadhaviji at: 1/8/2011 3:41 PM (13 Replies)

Rating (0)

Thanks 0

14 Entries

Entries per page: 10 | all

1/8/2011 3:41 PM	Rate (0)
Gadhaviji Advanced Member Joined: 1/5/2011 Last visit: 2/15/2017 Posts: 63 Rating: (1)	Dear Expert, I am trying to change NCK address of CCU 2 from HT6.I did below process forNCK 1.Power OnSystem 2. Acess level Manufacture. 3. NC 4.NCK Address 5.Enter 6 tonew NCK add 6.Save 7.OK 8.Error"Error while writing DDE variable" 9.Massage "NCK address not change" In HT 6 for HMI did below process. 1.Acess level Manufacture. 2.HMI (I can see two option ,One is Action log and second is DOS editor) 3.DOS editor 4.Error "Error on opening bedien.dat" Finaly i am not able to change address in NCK and HMI. I have check same process using PCU 20,seme problem is comming. Please guide me. Reg. Hinglaj
	Last edited by: Gadhaviji at: 1/9/2011 8:44 AM Dear Expert, Same i have tried in PCU50 840D system,it is possible. So please help me for PCU20 and HT6 with 810D system. Reg. Hingalj Last edited by: Gadhaviji at: 1/8/2011 3:52 PM
Suggestion To thank Quote Answer

1/9/2011 4:12 PM	Rate (0)
Ekalavya Platinum Expert Joined: 8/4/2009 Last visit: 5/31/2020 Posts: 2964 Rating: (463)	Hello.... Can your try using Simatic Field PG/Laptop with HMI advanced PC/PG loaded and check the NCK address change in CCU? Check it out hope this will solve your problem..... Regards, Ekalavya
	With Best Regards, Ekalavya
Suggestion To thank Quote Answer

1/10/2011 7:26 AM	Rate (0)
Gadhaviji Advanced Member Joined: 1/5/2011 Last visit: 2/15/2017 Posts: 63 Rating: (1)	Dear Expert, I will try to change NCK addressby HMI advance using PG,i will update you for same. But how to change Address in HT6. If i change NCK address in CCU then H6 will not communicate. Machine Brief idea. --- Machine is with CCU1 and CCU2,both CCU is connected through MPI. --- PCU20 is connected with CCU1 with NCK address 3. ---HT6 is connected with CCU2 with NCK address 6. But my new HT6 is communicating with NCK address 3 only. Please help me how to change NCK address in HT6.

Suggestion To thank Quote Answer

1/13/2011 1:01 PM	Rate (0)
Gadhaviji Advanced Member Joined: 1/5/2011 Last visit: 2/15/2017 Posts: 63 Rating: (1)	Dear Expert. PLease reply i amwaiting for your reply. Reg Hinglaj Gadhavi

Suggestion To thank Quote Answer

1/16/2011 11:05 AM	Rate (0)
Gadhaviji Advanced Member Joined: 1/5/2011 Last visit: 2/15/2017 Posts: 63 Rating: (1)	Hello Expert, Any solution please. Reg. Hinglaj

Suggestion To thank Quote Answer

1/16/2011 2:29 PM	Rate (0)
MBA Gold Member Joined: 3/19/2006 Last visit: 1/3/2021 Posts: 592 Rating: (76)	doconcd or doconweb . Once you have changed the MPI configuration you must regenerate the system software of the HT 6 and transfer it to the HT 6 via PC card. This action is described in detail in: References: /IAM/ IBN HMI Chapter: Installation and Start-Up of SINUMERIK HT 6 Note MPI addressThe default setting of the MPI address is 14D (decimal). We recommend keeping the MPI address. If you change the MPI address you must also adapt the GD circle parameterization. See Section 7.6, Page 7-175. Data transfer rate The data transfer rate is automatically recognized by HT 6.

Suggestion To thank Quote Answer

1/16/2011 2:53 PM	Rate (0)
Gadhaviji Advanced Member Joined: 1/5/2011 Last visit: 2/15/2017 Posts: 63 Rating: (1)	Dear MBA, Thanks for reply, I have gone through Docon,but i am not able to understand. Please help me how to configure this address in HT6 and How to generate system software. PLease what are tools required to perform this job? Reason for address change: In our machine two CCU are using.CCU1 is communicating with PCU20 NCK address 3and CCU2 is communicating with HT6 NCk address 6 .Both CCU is communicating through MPI. Now i have problem in HT6,so i want to change HT6.I have purchased HT6. New HT6 is only communicating with NCk address 3, but our requirement is to communicate with NCK address 6. PLease help me to change this address. Exatly mention what are software and hardware are required to finshed this job?

Suggestion To thank Quote Answer

1/16/2011 6:25 PM	Rate (0)
MBA Gold Member Joined: 3/19/2006 Last visit: 1/3/2021 Posts: 592 Rating: (76)	The simplest way is the copy of the old system HT6 in the PDF File is a description for the PCU20 I think it's the same with the HT6 generate a (*. ABB) File from the old HT6 and copy it to the new Attachment EN_A024 Harddisk_backup_pl.pdf (120 Downloads)

Suggestion To thank Quote Answer

1/17/2011 5:17 PM	Rate (0)
Gadhaviji Advanced Member Joined: 1/5/2011 Last visit: 2/15/2017 Posts: 63 Rating: (1)	Thanks MBA I will check and update you. I don't have blank Card, I have 8MB card but it is with System software,shall i use this? Reg. Hinglaj

Suggestion To thank Quote Answer

1/18/2011 3:47 AM	Rate (0)
Ekalavya Platinum Expert Joined: 8/4/2009 Last visit: 5/31/2020 Posts: 2964 Rating: (463)	Gadhaviji Thanks MBA I will check and update you. I don't have blank Card, I have 8MB card but it is with System software,shall i use this? Reg. Hinglaj Hi... No... system card don't distrub... You need to use compact flash cardwhich sits on the pcu 20... regards Ekalavya
	With Best Regards, Ekalavya
Suggestion To thank Quote Answer

1/18/2011 4:29 PM

Rate (0)

Gadhaviji

Advanced Member

Joined: 1/5/2011

Last visit: 2/15/2017

Posts: 63

Rating:

(1)

hi expert

i have below blank card, shall i use?

6FC53132AG000AA2

Reg.
Hinglaj

1/18/2011 4:35 PM

Rate (0)

Ekalavya

Platinum Expert

Joined: 8/4/2009

Last visit: 5/31/2020

Posts: 2964

Rating:

(463)

Gadhaviji
hi expert

i have below blank card, shall i use?

6FC53132AG000AA2

Reg.
Hinglaj

Yes you can use it... compact flash card 64MB...when your plugging in to the control you need to use with the adapter...ensure it is properly formatted before gettting in to the machine.

Regards,
Ekalavya

With Best Regards,
Ekalavya

1/18/2011 4:50 PM	Rate (0)
Gadhaviji Advanced Member Joined: 1/5/2011 Last visit: 2/15/2017 Posts: 63 Rating: (1)	Dear Ekalavya, Thanks In HT6 PCMCIA slot isalready available, then what is adapter? I will used blank card for this.

Suggestion To thank Quote Answer

1/18/2011 5:00 PM	Rate (0)
Ekalavya Platinum Expert Joined: 8/4/2009 Last visit: 5/31/2020 Posts: 2964 Rating: (463)	it is for PCU 20..... Regards, Ekalavya
	With Best Regards, Ekalavya
Suggestion To thank Quote Answer

Share this page:

Share this page on...

Created by: Gadhaviji at: 1/8/2011 3:41 PM (13 Replies)

Rating (0) Thanks 0

14 Entries

Entries per page: 10 | all

Last edited by: Gadhaviji at: 1/9/2011 8:44 AM

Last edited by: Gadhaviji at: 1/8/2011 3:52 PM

Attachment

14 Entries

Entries per page: 10 | all

All about SINUMERIK CNC automation systems

Follow us on

Rating (0)

Thanks 0