Skip to Content

support.automation.siemens.com | Technical Forum | Monday, March 01, 2021 3:29:25 AM

Print

QVZ error

Created by: Saul at: 7/16/2007 3:52 PM (8 Replies)

Rating (0)

Thanks 0

9 Entries

7/16/2007 3:52 PM	Rate (0)
Saul Posts: 5 Rating: (0)	S5 CPU keeps going into STOP showing QVZ and BSP LEDs. In I stack cause of interrupt is listed as QVZ time out: due to direct I/O access with byte - NR 200 Can anyone help as to waht the cause of this may be????? Thanks Saul
Saul Posts: 5 Rating: (0)
Suggestion To thank Quote Answer

7/16/2007 11:17 PM	Rate (0)
Late Platinum Expert Joined: 1/7/2006 Last visit: 11/21/2020 Posts: 2705 Rating: (302)	Dear Saul, QVZ menas that the I/O-card is not answering in 60 microseconds and then is giving that error. For U-perifery it could be that the power on the first 3 pins of the card is not ok. But normally the card is defect, you have to replace the card with that address.
	I hope that the answer will help, if you have still questions, don't hesitate to ask me. All the best, Late Never say never, think in solutions, not in trouble......
Suggestion To thank Quote Answer

10/5/2007 10:11 AM	Rate (0)
Thomarzali Posts: 8 Rating: (0)	Hi, Saul, This QVZ error could be occured depends on PROFIBUS cable connection error, connector problem or interface modul or PROFIBUS cable problem may be cable is broken somewhere. Please check this points carefully. After that the QVZ error will be gone. I hope this information helpful for you. Regards. Emir
Thomarzali Posts: 8 Rating: (0)
Suggestion To thank Quote Answer

10/9/2007 1:01 PM	Rate (0)
pago06 Posts: 36 Rating: (1)	Hi all, I'm having the same QVZ error on a S5-135 928B. I detected it while i was trying to output some values on a 470-4UC Analog Module and i get nothing to the output. The error disapears if i deletefrom PLC thePB or de call to the FB where i'm using that card (Channel). Could this be a simple misaddressing? Am i using the wrong channel (i.e.: KF +192)? Need some help debugging this..... Thanks for replying Goncalves
pago06 Posts: 36 Rating: (1)
Suggestion To thank Quote Answer

10/19/2007 5:18 AM	Rate (0)
kid237 Posts: 158 Rating: (3)	Hi, i seem to have the QVZ error too, but i am not sure if the I/O-card is defective, can anyone assist me on hw to troubleshoot this??? thank you.
kid237 Posts: 158 Rating: (3)
Suggestion To thank Quote Answer

11/11/2020 3:03 AM	Rate (0)
Faturrakhman Member Joined: 11/11/2020 Last visit: 11/11/2020 Posts: 2 Rating: (0)	Hello, I have a trouble with siemens S5. The problem is QVZ error. We already change the card. And it still error. Can you give me suggestion about this problem? How to check the configuration with the siemens S5? Thankyou.

Suggestion To thank Quote Answer

11/11/2020 3:45 AM	Rate (0)
ixo65 Grandmaster Joined: 12/18/2014 Last visit: 3/1/2021 Posts: 21528 Rating: (2371)	Faturrakhman Hello, I have a trouble with siemens S5. The problem is QVZ error. We already change the card. And it still error. Can you give me suggestion about this problem? How to check the configuration with the siemens S5? Thankyou. With only so minimal informations can nobody help you. Which S5? Which card mean you? Please make screenshots of the I-stack and the B-stack and show they us ...

Suggestion To thank Quote Answer

11/11/2020 4:04 AM	Rate (0)
Faturrakhman Member Joined: 11/11/2020 Last visit: 11/11/2020 Posts: 2 Rating: (0)	S5 Simatic. We change I/O module.

Suggestion To thank Quote Answer

11/11/2020 4:13 AM	Rate (0)
ixo65 Grandmaster Joined: 12/18/2014 Last visit: 3/1/2021 Posts: 21528 Rating: (2371)	An S5 is always a SIMATIC. You didn't even have to answer that. Which type? S5-100U? Which CPU type? CPU 100, 102 or 103? S5-115U? Which CPU type? CPU 941, 942, 943, 944, 945? S5-135U? Which CPU type? CPU 928? CPU 928B? S5-155U? We need exact information. And definitely screenshots from the I-Stack and the B-Stack.

Suggestion To thank Quote Answer