Skip to Content

support.automation.siemens.com | Technical Forum | Thursday, January 21, 2021 3:48:57 AM

Print

Setpoint command from

Created by: ensark2 at: 11/9/2012 7:26 AM (5 Replies)

Rating (1)

Thanks 1

6 Entries

11/9/2012 7:26 AM	Rate (0)
ensark2 Bronze Member Joined: 11/18/2009 Last visit: 5/4/2020 Posts: 262 Rating: (18)	I am trying to send Setpoint command from SICAM SCC but the value of the command is always 0 no matter which value I set in command. I use a button with C script to send it void PAS_Command_Float_V500(char* p_cTagName, float p_fValue, DWORD p_dwValueType, DWORD p_dwDuration) char* p_cTagName I set my TAG for this setpoint command, float p_fvalue I have tried to set I number (77) or internal float tag. DWORD p_dwValueType I put 22 according to manual this is Setpoint analog, floating point DWORD p_dwDuration I tried to set 0 or 5 SICAM SCC sends value but value is always 0. Has anyone experience with this?

Suggestion To thank Quote Answer

11/12/2012 12:34 PM	Rate (0)
Mike J Platinum Expert Joined: 10/9/2007 Last visit: 1/19/2021 Posts: 1118 Rating: (103)	Hi Ensark is the setpoint going to a Siprotec or to Automation in PAS? in the value, try 77.0 (with the decimal point) duration always 0 in value viewer take a look at cause, additional cause and other values. They will probably tell youif the command is being rejected. Mike
	Last edited by: Mike J at: 11/12/2012 12:35 PM Energy Automation products: Sicam, Siprotec, Digsi
Suggestion To thank Quote Answer

11/12/2012 11:26 PM	Rate (0)
ensark2 Bronze Member Joined: 11/18/2009 Last visit: 5/4/2020 Posts: 262 Rating: (18)	Hi Mike, this SCC is connected to AK 1703 via IEC 104 so I dont have value viewer. I dont use SICAM PAS here. But in Data flow of AK I can see that AK receive this command but value is 0. Also in wireshark I can see that value is 0. I have also tested with decimal point but no use. Best Regards Ensar

Suggestion To thank Quote Answer

11/13/2012 9:23 AM	Rate (0)
Mike J Platinum Expert Joined: 10/9/2007 Last visit: 1/19/2021 Posts: 1118 Rating: (103)	hi Ensark can you test it using a IEC104 simulator?
	Energy Automation products: Sicam, Siprotec, Digsi
Suggestion To thank Quote Answer

11/14/2012 11:15 PM	Rate (1)
ensark2 Bronze Member Joined: 11/18/2009 Last visit: 5/4/2020 Posts: 262 Rating: (18)	Solved Mike. Use different TI.

Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users Mike J

10/16/2014 4:33 PM	Rate (0)
mertz Posts: 9 Rating: (0)	Hi I have a problem regarding setpoint in SCC. I am using the same functionvoid PAS_Command_Float_V500(char* p_cTagName, float p_fValue, DWORD p_dwValueType, DWORD p_dwDuration). How did you solve it? What is "TI" your last response was "Use different TI" is that the value type from SICAM PAS? Best regards, Gabriel.
mertz Posts: 9 Rating: (0)
Suggestion To thank Quote Answer