Skip to Content

support.automation.siemens.com | Technical Forum | Saturday, March 06, 2021 3:56:50 AM

Print

SINAMICS G120 - CU240E-2DP - Slow Jog response

Created by: simaticfan79 at: 5/2/2012 6:54 PM (15 Replies)

Rating (0)

Thanks 0

Result pages:: |; 1 | 2; |

16 Entries

Entries per page: 10 | all

5/2/2012 6:54 PM	Rate (0)
simaticfan79 Experienced Member Joined: 1/4/2011 Last visit: 3/1/2021 Posts: 22 Rating: (0)	Dear colleagues, I am using SINAMICS CU240E-2 DP with 7.5kW power module. My question is, how to increase motor response while Jogging? It takes quite long time before motor starts to rotate under load when jog function is requested. I would like motor to start almost instantly when Jog is requested. Any suggestions how to solve this issue? What parameters to set? Thank You!

Suggestion To thank Quote Answer

5/3/2012 3:57 PM	Rate (0)
Ashutosh Kr Bronze Member Joined: 3/15/2011 Last visit: 11/10/2020 Posts: 134 Rating: (9)	What Values have you placed on p1047 & p1048 . Make p1047 and p1048 to 5s ..

Suggestion To thank Quote Answer

5/3/2012 8:02 PM	Rate (0)
Barlera Experienced Member Joined: 2/21/2011 Last visit: 9/10/2020 Posts: 52 Rating: (11)	Hello simaticfan79 You could change the parameter p1058 and/or p1059. See attached file. Best Regards, Henrique Barlera Attachment Pages from [Copy of PLI_CU240BE_en_V44_012011].pdf (273 Downloads)

Suggestion To thank Quote Answer

5/3/2012 8:06 PM	Rate (0)
simaticfan79 Experienced Member Joined: 1/4/2011 Last visit: 3/1/2021 Posts: 22 Rating: (0)	Ashutosh Kr: p1047and p1048 are set to 5s. I have tried with less, but same results. I want ramps to be ignored when jogging = instant start. Jog speed is set low - for inching the machine. But I need ramps for regular startup. Barlera: I have set Jog speed at 250 rpm. That speed is for inching the machine. Normal working speed is around 3000 rpm. I just want motor to move instantly after JOG is required. Now it takes too long and it is annoying to wait few seconds for motor to move while machine is setting. Tnx
	Last edited by: simaticfan79 at: 5/3/2012 9:25 PM
Suggestion To thank Quote Answer

5/3/2012 9:23 PM	Rate (0)
0_Einstein Diamond Member Joined: 7/7/2010 Last visit: 3/5/2021 Posts: 10212 Rating: (1699)	simaticfan79 p1047and p1048 are set to 5s. I have tried with less, but same results. I want ramps to be ignored when jogging = instant start. Jog speed is set low - for inching the machine. But I need ramps for regular startup. Tnx For jog, set your ramp rate to as low a value as the drive accepts without faulting. For example, you might be able to set it to 0.5 seconds and get much faster jog response.
	science guy
Suggestion To thank Quote Answer

5/3/2012 9:26 PM	Rate (0)
simaticfan79 Experienced Member Joined: 1/4/2011 Last visit: 3/1/2021 Posts: 22 Rating: (0)	huggy_d1: Yes I will get faster results for jog, but I need ramps for normal operation... So how can I disable ramps or set ramps to 0 for JOG and use 5s ramp for normal startup? Tnx!

Suggestion To thank Quote Answer

5/3/2012 11:07 PM	Rate (0)
0_Einstein Diamond Member Joined: 7/7/2010 Last visit: 3/5/2021 Posts: 10212 Rating: (1699)	simaticfan79 huggy_d1: Yes I will get faster results for jog, but I need ramps for normal operation... So how can I disable ramps or set ramps to 0 for JOG and use 5s ramp for normal startup? Tnx! P1120/1121 are ramp rates for normal operation. Set those to 5s. P1060/1061 is for JOG, so set those to a very small number that achieves acceptable results without faults. To enable/disable JOG ramp times (for testing), P1164 set to 1 will put your fast jog ramp times in for your normal speeds. Be careful. This should probably be set to 0 and stay at 0.
	science guy
Suggestion To thank Quote Answer

5/4/2012 2:47 AM	Rate (0)
simaticfan79 Experienced Member Joined: 1/4/2011 Last visit: 3/1/2021 Posts: 22 Rating: (0)	huggy_d1: In parameter manual for G120 there are no P1060/1061 and P1064 parameters
	Last edited by: simaticfan79 at: 5/4/2012 3:02 AM
Suggestion To thank Quote Answer

5/4/2012 4:26 AM	Rate (0)
0_Einstein Diamond Member Joined: 7/7/2010 Last visit: 3/5/2021 Posts: 10212 Rating: (1699)	simaticfan79 huggy_d1: In parameter manual for G120 there are no P1060/1061 and P1064 parameters My mistake. I am using a similar drive, the CU240S-DP, and pulled up the entries for that drive. I figured that since the CU240E-2 was supposed to be the replacement for the now End-of-life CU240S-DP family, the parameters and options would be similar. Unless someone knows the simple way to configure the drive, you might want to have a digital input for the jog use a different set of parameters. For example, for automatic (no jogging), you would use index[0] data sets. For jogging, you would instruct the drive to use index[1] parameters. Then set the jog ramp rates for P1120[1] much faster than P1120[0]. Now, do not ask me _how_, but it has to be possible with all that BICO technology and there must be experts here who can guide you further. Sorry about the mistake and leading you away from the answer.
	science guy
Suggestion To thank Quote Answer

5/4/2012 2:47 PM	Rate (0)
Technology Team Platinum Expert Joined: 10/11/2006 Last visit: 3/5/2021 Posts: 4698 Rating: (589)	Hello, please test your application, when the drive keeps in operation. So don`t use the jog bits. You can switch on your drive with OFF2(p844/845)/OFF3(p848/849) set OFF1 (p840)and Enable operation (p852). So you would get in r002 = 0 : Operation - everything enabled Than you can use the Fixed Setpoints for the speed setpoints. I suppose your problem is: After JOG your pulses are disabled - see r002. Than you press JOG and first the motor excitation build-up time in p346 will be active.
	With best regards, Technology Team Application consulting and pre sales support for SINAMICS, SIMATIC Technology, SIMOTION, SIMOTICS and MOTION CONNECT
Suggestion To thank Quote Answer