10/2/2012 3:29 PM | |
Posts: 4 Rating: (0) |
What is the status of the lights on the NCU? Which light it red? Which is yellow? |
10/3/2012 5:56 AM | |
Posts: 33 Rating: (0) |
Hello sir, I will attached a picture so you can help me figure out. Tnx. Gerry |
Last edited by: O_Moderator at: 10/11/2012 11:13 AM |
|
10/4/2012 3:06 AM | |
Posts: 33 Rating: (0) |
Hello sir, I have attached a picture of the NCU. Hope you can all help me on this problem. gerab |
Last edited by: O_Moderator at: 10/11/2012 11:15 AM |
|
10/9/2012 3:14 PM | |
Joined: 8/11/2009 Last visit: 4/26/2023 Posts: 10 Rating: (0) |
What other error messages are displayed? |
10/10/2012 6:35 AM | |
Posts: 664 Rating: (17) |
Hai Gerab, If you have PLC.arc original backup in your hand, Please try to clear PLC and reload the backup. Thanks&Regards, Raj
|
10/10/2012 3:20 PM | |
Joined: 8/11/2009 Last visit: 4/26/2023 Posts: 10 Rating: (0) |
Yes, you'll have to clear the PLC side (S4) then reload the last PLC Project from the HMI or S7. |
10/11/2012 3:55 AM | |
Posts: 33 Rating: (0) |
Hello sir, How to clear PLC? Gerab |
10/11/2012 5:55 AM | |
Posts: 2964 Rating: (478)
|
Hello, Check this link:-) /tf/WW/en/Posts/45967#top Regards, Prakash |
10/19/2012 3:52 AM | |
Posts: 33 Rating: (0) |
Hello, You mean I am going to transfer the cablefrom x101 to x122 Gerab |
10/19/2012 6:01 AM | |
Posts: 664 Rating: (17) |
Hai gerab, Please check the attachment,.. Thanks&Regards, Raj
AttachmentNCU-Connection.pdf (237 Downloads) |
10/19/2012 12:06 PM | |
Posts: 664 Rating: (17) |
Hai gerab, Please try to restart machine and laptop/pc.and then check..and revert back please... Thanks®ards, Raj |
10/22/2012 3:10 AM | |
Posts: 33 Rating: (0) |
Hello sir, When I go to hardware diagnostic I noticed that a faulty cpu and dp slave appears. I attached a picture. Gerab |
10/22/2012 8:55 AM | |
Posts: 33 Rating: (0) |
hello sir, Here is the picture when i go tocpu module information. Gerab |
10/22/2012 9:04 AM | |
Posts: 33 Rating: (0) |
Hello sir, When i GO TO diagnostic buffer this is the picture. Gerab |
10/22/2012 9:10 AM | |
Posts: 33 Rating: (0) |
Hello sir, This is the picture when i go to dp slave information. Gerab |
10/22/2012 9:15 AM | |
Posts: 33 Rating: (0) |
HEllo sir. This is also the picture when i go to dp slave diagnosis. Gerab |
11/5/2012 1:23 AM | |
Posts: 33 Rating: (0) |
Hello sir, |
11/16/2012 3:33 AM | |
Posts: 33 Rating: (0) |
Hello sir, Is it possible that the reason why the IR module led is green beacuse of the emergency stop 3000 error? Gerab |
11/18/2012 11:21 AM | |
Joined: 4/23/2010 Last visit: 12/31/2023 Posts: 8092 Rating: (872) |
The GREEN LED indication signifies as there are no enable signal presents. Please see the attached file here with. Please check your PLC ladder logic.
AttachmentC:\Documents and Settings\ntguest\Desktop\IR module LED significance.pdf (320 Downloads) |
Follow us on