Skip to Content

support.automation.siemens.com | Technical Forum | Tuesday, March 09, 2021 9:11:43 AM

Print

The following devices are not consistent online

Created by: rdoliveira at: 7/1/2013 10:21 PM (15 Replies)

Rating (0)

Thanks 0

16 Entries

Entries per page: 10 | all

7/1/2013 10:21 PM	Rate (0)
rdoliveira Gold Member Joined: 4/26/2012 Last visit: 2/2/2021 Posts: 731 Rating: (54)	log Information:------------------------------------------------------------------ Information:The following devices are not consistent online: Drive_unit_1. Information:Drive_unit_1: Uploading DRIVE-CLiQ set topology... Information:Drive_unit_1: Uploading DRIVE-CLiQ actual topology... Information:Drive_unit_1: Control_Unit: Drive object has been uploaded. Information:Drive_unit_1: SERVO_02: Drive object has been uploaded. Information:Drive_unit_1: Upload completed Information:Project successfully loaded to the PG Attachment not.jpg (98 Downloads)
	Obrigado.
Suggestion To thank Quote Answer

7/2/2013 2:31 AM	Rate (0)
Ashutosh Kr Bronze Member Joined: 3/15/2011 Last visit: 11/10/2020 Posts: 134 Rating: (9)	the problem is in the topology comparison is ok. see the topology is red which is inconsistence.add the snapshot of topology section ,then it will be clear which additional device which you have included in your project. regards Ashutosh Attachment not.zip (60 Downloads)

Suggestion To thank Quote Answer

7/2/2013 11:05 AM	Rate (0)
viralpatel Silver Member Joined: 11/18/2010 Last visit: 2/10/2021 Posts: 522 Rating: (31)	rdoliveira log Information:------------------------------------------------------------------ Information:The following devices are not consistent online: Drive_unit_1. Information:Drive_unit_1: Uploading DRIVE-CLiQ set topology... Information:Drive_unit_1: Uploading DRIVE-CLiQ actual topology... Information:Drive_unit_1: Control_Unit: Drive object has been uploaded. Information:Drive_unit_1: SERVO_02: Drive object has been uploaded. Information:Drive_unit_1: Upload completed Information:Project successfully loaded to the PG Hi , it tells That your open program and uploaded program are not matching or topology are different viral patel
	Last edited by: viralpatel at: 7/2/2013 11:13 AM
Suggestion To thank Quote Answer

7/2/2013 1:20 PM	Rate (0)
rdoliveira Gold Member Joined: 4/26/2012 Last visit: 2/2/2021 Posts: 731 Rating: (54)	Ashutosh Kr the problem is in the topology comparison is ok. see the topology is red which is inconsistence.add the snapshot of topology section ,then it will be clear which additional device which you have included in your project. regards Ashutosh What is in red is the technology, I'm just testing with a Technology CPU, what I know is about Drive_unit_1
	Obrigado.
Suggestion To thank Quote Answer

7/2/2013 1:24 PM	Rate (0)
rdoliveira Gold Member Joined: 4/26/2012 Last visit: 2/2/2021 Posts: 731 Rating: (54)	viralpatel rdoliveira log Information:------------------------------------------------------------------ Information:The following devices are not consistent online: Drive_unit_1. Information:Drive_unit_1: Uploading DRIVE-CLiQ set topology... Information:Drive_unit_1: Uploading DRIVE-CLiQ actual topology... Information:Drive_unit_1: Control_Unit: Drive object has been uploaded. Information:Drive_unit_1: SERVO_02: Drive object has been uploaded. Information:Drive_unit_1: Upload completed Information:Project successfully loaded to the PG Hi , it tells That your open program and uploaded program are not matching or topology are different viral patel If you look the picture, is the Drive_unit_1 that is showing the information highlighted in blue and red
	Obrigado.
Suggestion To thank Quote Answer

7/2/2013 5:21 PM	Rate (0)
Ashutosh Kr Bronze Member Joined: 3/15/2011 Last visit: 11/10/2020 Posts: 134 Rating: (9)	the red means that your drive unit 1 is inconsistent. upload your topology window and compare project set specified,and actual ,state regards Ashutosh

Suggestion To thank Quote Answer

7/3/2013 8:17 AM	Rate (0)
Technology Team Platinum Expert Joined: 10/11/2006 Last visit: 3/8/2021 Posts: 4701 Rating: (589)	Hello rdoliviera, according to your log, an upload was done after the comparison. So after uploading, the system shows consistency, as thereare no red flags on your drive objects any more.
	With best regards, Technology Team Application consulting and pre sales support for SINAMICS, SIMATIC Technology, SIMOTION, SIMOTICS and MOTION CONNECT
Suggestion To thank Quote Answer

7/3/2013 12:59 PM	Rate (0)
rdoliveira Gold Member Joined: 4/26/2012 Last visit: 2/2/2021 Posts: 731 Rating: (54)	TechTeam Hello rdoliviera, according to your log, an upload was done after the comparison. So after uploading, the system shows consistency, as thereare no red flags on your drive objects any more. OK, do not have red flag, but these warnings will not let me move the engine because it is not "ready".
	Obrigado.
Suggestion To thank Quote Answer

7/3/2013 1:03 PM	Rate (0)
rdoliveira Gold Member Joined: 4/26/2012 Last visit: 2/2/2021 Posts: 731 Rating: (54)	Expert list, not ready. Attachment Expert.jpg (85 Downloads)
	Obrigado.
Suggestion To thank Quote Answer

7/3/2013 1:28 PM	Rate (0)
Technology Team Platinum Expert Joined: 10/11/2006 Last visit: 3/8/2021 Posts: 4701 Rating: (589)	Did you finish all commissiong steps before? Do you get any fault message when changing p10 to 0? The drive is deactivated, as your drive isstill in commissioning mode, which has to exit beforeit can run.
	With best regards, Technology Team Application consulting and pre sales support for SINAMICS, SIMATIC Technology, SIMOTION, SIMOTICS and MOTION CONNECT
Suggestion To thank Quote Answer

7/3/2013 1:35 PM	Rate (0)
rdoliveira Gold Member Joined: 4/26/2012 Last visit: 2/2/2021 Posts: 731 Rating: (54)	Not finished, because the CU305 does not read the data on the servomotor. So I can not put 0 in p10. Attachment p10.jpg (56 Downloads)
	Obrigado.
Suggestion To thank Quote Answer

7/3/2013 3:12 PM	Rate (0)
ChristophD Grandmaster-Expert Joined: 5/12/2006 Last visit: 3/8/2021 Posts: 18868 Rating: (2359)	Hello, please post the project here so we can help you ! Regards Christoph

Suggestion To thank Quote Answer

7/3/2013 3:32 PM	Rate (0)
rdoliveira Gold Member Joined: 4/26/2012 Last visit: 2/2/2021 Posts: 731 Rating: (54)	project Attachment CU305.zip (28 Downloads)
	Obrigado.
Suggestion To thank Quote Answer

7/3/2013 4:32 PM	Rate (0)
ChristophD Grandmaster-Expert Joined: 5/12/2006 Last visit: 3/8/2021 Posts: 18868 Rating: (2359)	Hello, how you create the configuration? In the project i see thats a syncronous Servo Motor ist configured and a encoder interface SMC30. If have a motor with DRIVE-CLiQ interface you can do the following: make a automatic configuration online or configure "Motor with DRIVE-CLiQ" Interface offline and download it. Regards Christoph

Suggestion To thank Quote Answer

7/3/2013 4:46 PM	Rate (0)
rdoliveira Gold Member Joined: 4/26/2012 Last visit: 2/2/2021 Posts: 731 Rating: (54)	ChristophD Hello, how you create the configuration? In the project i see thats a syncronous Servo Motor ist configured and a encoder interface SMC30. If have a motor with DRIVE-CLiQ interface you can do the following: make a automatic configuration online or configure "Motor with DRIVE-CLiQ" Interface offline and download it. Regards Christoph yes, tried both ways, and the problem continues, I believe that is the problem CU305
	Obrigado.
Suggestion To thank Quote Answer

7/3/2013 8:06 PM	Rate (0)
Ashutosh Kr Bronze Member Joined: 3/15/2011 Last visit: 11/10/2020 Posts: 134 Rating: (9)	take a back up and try factory reset your drive , regards Ashutosh

Suggestion To thank Quote Answer